--- 1/draft-ietf-bess-mvpn-mib-05.txt 2018-04-30 17:13:31.784562193 -0700 +++ 2/draft-ietf-bess-mvpn-mib-06.txt 2018-04-30 17:13:31.908565180 -0700 @@ -1,27 +1,27 @@ Network Working Group Z. Zhang, Ed. Internet-Draft Juniper Intended status: Standards Track S. Asif -Expires: June 11, 2018 AT&T +Expires: November 1, 2018 AT&T A. Green BT S. Gulranjani Cisco P. Jain Alcatel-Lucent H. Tsunoda, Ed. Tohoku Institute of Technology - December 08, 2017 + April 30, 2018 BGP/MPLS Layer 3 VPN Multicast Management Information Base - draft-ietf-bess-mvpn-mib-05 + draft-ietf-bess-mvpn-mib-06 Abstract This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular, it describes managed objects to configure and/or monitor MVPN, Multicast in MultiProtocol Label Switching/Border Gateway Protocol (MPLS/BGP) IP Virtual Private Networks (VPNs) on a Provider Edge router. @@ -33,52 +33,52 @@ Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at http://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." - This Internet-Draft will expire on June 11, 2018. + This Internet-Draft will expire on November 1, 2018. Copyright Notice - Copyright (c) 2017 IETF Trust and the persons identified as the + Copyright (c) 2018 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2 1.1. Terminology . . . . . . . . . . . . . . . . . . . . . . . 3 2. The Internet-Standard Management Framework . . . . . . . . . 4 3. MCAST-VPN-MIB . . . . . . . . . . . . . . . . . . . . . . . . 4 3.1. Summary of MIB Module . . . . . . . . . . . . . . . . . . 4 - 3.2. MIB Module Definitions . . . . . . . . . . . . . . . . . 7 - 4. Security Considerations . . . . . . . . . . . . . . . . . . . 36 - 5. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 37 - 6. Acknowledgement . . . . . . . . . . . . . . . . . . . . . . . 37 - 7. References . . . . . . . . . . . . . . . . . . . . . . . . . 37 - 7.1. Normative References . . . . . . . . . . . . . . . . . . 37 - 7.2. Informative References . . . . . . . . . . . . . . . . . 39 - Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 39 + 3.2. MIB Module Definitions . . . . . . . . . . . . . . . . . 6 + 4. Security Considerations . . . . . . . . . . . . . . . . . . . 62 + 5. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 63 + 6. Acknowledgement . . . . . . . . . . . . . . . . . . . . . . . 64 + 7. References . . . . . . . . . . . . . . . . . . . . . . . . . 64 + 7.1. Normative References . . . . . . . . . . . . . . . . . . 64 + 7.2. Informative References . . . . . . . . . . . . . . . . . 66 + Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 66 1. Introduction [RFC6513], [RFC6514], and [RFC6625] specify procedures for supporting multicast in Border Gateway Protocol/MultiProtocol Label Switching (BGP/MPLS) Layer 3 (IP) Virtual Private Network (VPN). Throughout this document, we will use the term "Multicast VPN (MVPN)" [RFC6513] to refer to a BGP/MPLS IP VPN that supports multicast. Provider Edge routers (PEs) exchange the VPN customer multicast @@ -116,24 +116,24 @@ send customer multicast traffic to all or some PEs in the same VPN. There are two kinds of PMSI: "Inclusive PMSI (I-PMSI)" and "Selective PMSI (S-PMSI)" [RFC6513]. An I-PMSI is a PMSI that enables a PE attached to a particular MVPN to transmit a message to all PEs in the same VPN. An S-PMSI is a PMSI that enables a PE attached to a particular MVPN to transmit a message to some of the PEs in the same VPN. As described in [RFC4382], each PE router maintains one default - forwarding table and "VPN Routing and Forwarding tables", or "VRFs". - Throughout this document, we will use the term "multicast VRF (MVRF)" - to refer a VRF that is configured to contain the multicast routing - information. + forwarding table and "Virtual Routing and Forwarding tables", or + "VRFs". Throughout this document, we will use the term "multicast + VRF (MVRF)" to refer a VRF that is configured to contain the + multicast routing information. Interchangeably, the term MVRF and MVPN are used to refer to a particular Multicast VPN instantiation on a particular PE. The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119]. 2. The Internet-Standard Management Framework @@ -150,178 +150,152 @@ RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580 [RFC2580]. 3. MCAST-VPN-MIB This document defines MCAST-VPN-MIB, a MIB module for monitoring and/ or configuring MVPNs on PEs. 3.1. Summary of MIB Module - The configuration and states specific to an MVPN include the - following information elements: - - o C-multicast routing information exchange protocol (PIM or BGP) - - o I-PMSI, S-PMSI and corresponding P-tunnels + MCAST-VPN-MIB provides the following functionalities for monitoring + and configuring MVPN. - o Mapping of C-multicast routing information to PMSI tunnels + o Monitoring attribute informations of MVRFs of MVPNs presented on a + PE - To represent these information elements, MCAST-VPN-MIB defines eight - tables: mvpnGeneralTable, mvpnBgpGeneralTable, mvpnSpmsiConfigTable, - mvpnPmsiConfigTable, mvpnIpmsiTable, mvpnInterAsIpmsiTable, - mvpnSpmsiTable, mvpnMrouteTable. + o Configuring some timers related to a MVRF - The following four tables represent the MVPN configurations on PEs. + o Notifying creation, deletion, and modification of MVRFs on a PE - o mvpnGeneralTable + o Monitoring attribute informations of PMSIs on a PE - o mvpnBgpGeneralTable + o Monitoring advertisement exchanged by a PE - o mvpnSpmsiConfigTable + o Monitoring routing entries in an MVRF - o mvpnPmsiConfigTable + o Monitoring information on next-hops in an MVRF - The following diagram shows the relationship among those four tables - use for configuration. Each box in the diagram represents a table, - and the label of each box corresponds to a table name. An arrow - indicates that one table has a pointer to a row in another table. - The entry in mvpnGeneralTable and mvpnSpmsiConfigTable has a pointer - to the row pertaining to the entry in the mvpnPmsiConfigTable. + o Notifying events that a PE joins or leaves a multicast group - +--------------+ - | mvpnBgp | - | GeneralTable | - +--------------+ +-------------------+ +-----------------+ - | mvpnGeneral | | mvpnPmsiConfig | | mvpnSpmsiConfig | - | Table | -> | Table | <- | Table | - +--------------+ +-------------------+ +-----------------+ + To provide these functionalities, MCAST-VPN-MIB defines nine tables: + mvpnGenericTable, mvpnBgpGenericlTable, mvpnPmsiTable, + mvpnSpmsiTable, mvpnIpmsiAdvtTable, mvpnInterAsIpmsiAdvtTable, + mvpnSpmsiAdvtTable, mvpnMrouteTable, and mvpnMrouteNextHopTable. - o mvpnGeneralTable + The following two tables contain information of MVRFs of MVPNs + configured on a PE. - This table represents MVPNs that are configured on a PE. Each - entry in this table is created for each MVRF representing an - instance of MVPN. The entry represetns general configuration/ - states of the MVRF, including Inclusive PMSI (I-PMSI) - configuration. The MVPN represented by the entry in this table - must have the corresponding VRF in MPLS-L3VPN-STD-MIB [RFC4382]. + o mvpnGenericTable - o mvpnBgpGeneralTable + This table specifies the generic information about MVRFs present + in a PE. Each entry in this table is created for each MVRF + representing an instance of MVPN. The entry represetns general + configuration/states of the MVRF, including Inclusive PMSI + (I-PMSI) configuration. An MVRF represented by the entry in this + table must have a corresponding VRF in MPLS-L3VPN-STD-MIB + [RFC4382]. - This table augments the aformentioned mvpnGeneralTable. This - table contains BGP-MVPN specific managed objects. + o mvpnBgpGenericTable - o mvpnSpmsiConfigTable + This table specifies the specific information of MVRFs of MVPNs + that use BGP for exchanging C-Multicast routing information + present in a PE. Each MVRF of an MVPN that use BGP for exchanging + C-Multicast routing information will have an entry in this table. + The MVRF represented by this entry will have a corresponding entry + in the mvpnGenericTable. - This table contains managed objects necessary for configure - Selective PMSI (S-PMSI) associated with an MVRF on a PE. + The following two tables contain information of PMSIs configured on a + PE. - o mvpnPmsiConfigTable + o mvpnPmsiTable - This table contains managed objects common to both I-PMSI and - S-PMSI configurations. Both I-PMSI configuration (in the entry in - mvpnGeneralTable) and S-PMSI configuration (in the entry in + This table contains common managed objects representing attribute + information of both I-PMSI and Selective PMSI (S-PMSI) configured + on a PE. Both I-PMSI information (in the entry in + mvpnGeneralTable) and S-PMSI information (in the entry in mvpnSpmsiConfigTable) refer to an entry in this table. - The following four tables are designed for monitoring MVPNs on PEs. - - o mvpnIpmsiTable - - o mvpnInterAsIpmsiTable - o mvpnSpmsiTable - o mvpnMrouteTable - The following diagram shows the relationship among these four tables - and the l2l3VpnMcastPmsiTunnelAttributeTable defined separately in - L2L3-VPN-MCAST-MIB [I-D.ietf-bess-l2l3-vpn-mcast-mib]. The entry in - every table has a pointer to the row pertaining to the entry in the - l2l3VpnMcastPmsiTunnelAttributeTable. + This table contains managed objects representing attribute + information that is specific for S-PMSI associated with an MVRF on + a PE. - +--------------+ +-------------------+ +-----------------+ - | mvpnIpmsi | -> | l2L3VpnMcastPmsi | <- | mvpnSpmsi | - | Table | | TunnelAttribute | | Table | - +--------------+ | Table | +-----------------+ - -> +-------------------+ - / ^ - / | - +--------------+ +-------------------+ - | mvpnInterAs | | mvpnMrouteTable | - | IpmsiTable | +-------------------+ - +--------------+ + The following three tables are designed for monitoring advertisements + that is advertised/received by a PE. - o mvpnIpmsiTable + o mvpnIpmsiAdvtTable - This table contains managed objects for monitoring all Intra-AS - I-PMSIs advertised and received by a PE. This table contains all - advertised and received Intra-AS I-PMSIs. With PIM-MVPN, it is - applicable only when BGP-Based Autodiscovery of MVPN Membership is - used. + This table contains managed objects representing advertisements of + Intra-AS I-PMSIs advertised/received by a PE. - o mvpnInterAsIpmsiTable + o mvpnInterAsIpmsiAdvtTable + This table contains managed objects representing advertisements of + Inter-AS I-PMSIs advertised/received by a PE. - This table contains all advertised and received Inter-AS I-PMSIs. - With PIM-MVPN, it is applicable only when BGP-Based Autodiscovery - of MVPN Membership is used. + o mvpnSpmsiAdvtTable - o mvpnSpmsiTable + This table contains managed objects representing advertisements of + S-PMSIs advertised/received by a PE. - This table contains managed objects for monitoring all S-PMSIs - advertised and received by a PE. + The following two tables are designed for handling routing + information that is advertised/received by a PE. o mvpnMrouteTable - This table augments - ipMcastMIB.ipMcast.ipMcastRouteTable [RFC5132], for some MVPN - specific information. + This table contains multicast routing information in MVRFs present + in a PE. - o l2l3VpnMcastPmsiTunnelAttributeTable + o mvpnMrouteNextHopTable - An entry of this table corresponds to a PMSI Tunnel attribute and - is maintained by a PE router that advertises and receives the - attribute. Th entry in this table is referred by entries in - mvpnIpmsiTable, mvpnInterAsIpmsiTable, mvpnSpmsiTable, and - mvpnMrouteTable. + The table contains information on the next-hops on outgoing + interfaces for routing IP multicast datagrams in MVPNs present on + a PE. 3.2. MIB Module Definitions MCAST-VPN-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, - Gauge32, Unsigned32, mib-2 + Counter32, Counter64, Gauge32, Unsigned32, TimeTicks, + zeroDotZero, mib-2 FROM SNMPv2-SMI -- [RFC2578] MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF -- [RFC2580] - TruthValue, RowPointer, RowStatus, TimeStamp, TimeInterval + RowPointer, TimeStamp, TimeInterval FROM SNMPv2-TC -- [RFC2579] - SnmpAdminString - FROM SNMP-FRAMEWORK-MIB -- [RFC2571] + CounterBasedGauge64 + FROM HCNUM-TC -- [RFC2856] + + InterfaceIndex, InterfaceIndexOrZero + FROM IF-MIB -- [RFC2863] InetAddress, InetAddressType, InetAddressPrefixLength, InetAutonomousSystemNumber FROM INET-ADDRESS-MIB -- [RFC2851] mplsL3VpnVrfName, MplsL3VpnRouteDistinguisher FROM MPLS-L3VPN-STD-MIB -- [RFC4382] - ipMcastRouteEntry - FROM IPMCAST-MIB -- [RFC5132] + IANAipRouteProtocol, IANAipMRouteProtocol + FROM IANA-RTPROTO-MIB -- [RTPROTO] L2L3VpnMcastProviderTunnelType FROM L2L3-VPN-MCAST-TC-MIB; mvpnMIB MODULE-IDENTITY - LAST-UPDATED "201712081200Z" -- 8th December 2017 12:00:00 GMT + LAST-UPDATED "201804301200Z" -- 30th April 2018 12:00:00 GMT ORGANIZATION "IETF BESS Working Group." CONTACT-INFO " Zhaohui Zhang Juniper Networks, Inc. 10 Technology Park Drive Westford, MA 01886 USA Email: zzhang@juniper.net Saud Asif @@ -355,25 +329,25 @@ 35-1, Yagiyama Kasumi-cho Taihaku-ku, Sendai, 982-8577 Japan Email: tsuno@m.ieice.org Comments and discussion to bess@ietf.org" DESCRIPTION "This MIB contains managed object definitions for multicast in BGP/MPLS IP VPNs defined by [RFC6513]. - Copyright (C) The Internet Society (2017)." + Copyright (C) The Internet Society (2018)." -- Revision history. - REVISION "201712081200Z" -- 8th December, 2017 + REVISION "201804301200Z" -- 30th April, 2018 DESCRIPTION "Initial version, published as RFC XXXX." -- RFC Ed. replace XXXX with actual RFC number and remove this note ::= { mib-2 YYYY } -- IANA Reg.: Please assign a value for "YYYY" under the -- 'mib-2' subtree and record the assignment in the SMI -- Numbers registry. @@ -387,1061 +361,2318 @@ mvpnNotifications OBJECT IDENTIFIER ::= { mvpnMIB 0 } -- tables, scalars mvpnObjects OBJECT IDENTIFIER ::= { mvpnMIB 1 } -- conformance information mvpnConformance OBJECT IDENTIFIER ::= { mvpnMIB 2 } -- mvpn Objects mvpnScalars OBJECT IDENTIFIER ::= { mvpnObjects 1 } - mvpnGeneral OBJECT IDENTIFIER ::= { mvpnObjects 2 } + mvpnGeneric OBJECT IDENTIFIER ::= { mvpnObjects 2 } mvpnConfig OBJECT IDENTIFIER ::= { mvpnObjects 3 } mvpnStates OBJECT IDENTIFIER ::= { mvpnObjects 4 } -- Scalar Objects - mvpnMvrfs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION - "The total number of MVRFs that are present on - this Provider Edge router (PE), whether - for IPv4, IPv6, or mLDP C-Multicast." + "The total number of Multicast Virtual Routing and + Forwarding tables (MVRFs) that are present on + this Provider Edge router (PE). This includes MVRFs + for IPv4, IPv6, and mLDP C-Multicast. + " ::= { mvpnScalars 1 } mvpnV4Mvrfs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of MVRFs for IPv4 C-Multicast that are - present in this PE." + present in this PE. + " ::= { mvpnScalars 2 } mvpnV6Mvrfs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of MVRFs for IPv6 C-Multicast that are - present in this PE." + present in this PE. + " ::= { mvpnScalars 3 } mvpnPimV4Mvrfs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION - "The number of PIM-MVPN MVRFs for IPv4 C-Multicast that are - present in this PE." + "The number of MVRFs of MVPNs that use PIM for + exchanging IPv4 C-Multicast routing information + present in this PE. + " ::= { mvpnScalars 4 } mvpnPimV6Mvrfs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION - "The number of PIM-MVPN MVRFs for IPv6 C-Multicast that are - present in this PE." + "The number of MVRFs of MVPNs that use PIM for + exchanging IPv6 C-Multicast routing information + present in this PE. + " ::= { mvpnScalars 5 } mvpnBgpV4Mvrfs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION - "The number of BGP-MVPN MVRFs for IPv4 C-Multicast that are - present in this PE." + "The number of MVRFs of MVPNs that use BGP for + exchanging IPv4 C-Multicast routing information + present in this PE. + " ::= { mvpnScalars 6 } mvpnBgpV6Mvrfs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION - "The number of BGP-MVPN MVRFs for IPv6 C-Multicast that are - present in this PE." + "The number of MVRFs of MVPNs that use BGP for + exchanging IPv6 C-Multicast routing information + present in this PE. + " ::= { mvpnScalars 7 } mvpnMldpMvrfs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION - "The number of BGP-MVPN MVRFs for mLDP C-Multicast that are - present in this PE." + "The number of MVRFs of MVPNs that use BGP for + exchanging mLDP C-Multicast routing information + present in this PE. + " ::= { mvpnScalars 8 } - mvpnNotificationEnable OBJECT-TYPE - SYNTAX TruthValue - MAX-ACCESS read-write - STATUS current - DESCRIPTION - "If this object is TRUE, then the generation of all - notifications defined in this MIB is enabled." - DEFVAL { false } - ::= { mvpnScalars 9 } - - -- General MVRF Information Table + -- Generic MVRF Information Table - mvpnGeneralTable OBJECT-TYPE - SYNTAX SEQUENCE OF MvpnGeneralEntry + mvpnGenericTable OBJECT-TYPE + SYNTAX SEQUENCE OF MvpnGenericEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION - "This table specifies the general information about the MVRFs - present in this PE." - ::= { mvpnGeneral 1 } + "This table specifies the generic information about the MVRFs + present in this PE. - mvpnGeneralEntry OBJECT-TYPE - SYNTAX MvpnGeneralEntry + Entries in this table are not required to survive a reboot + of the managed entity. + " + ::= { mvpnGeneric 1 } + + mvpnGenericEntry OBJECT-TYPE + SYNTAX MvpnGenericEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION - "An entry in this table is created for each MVRF in the - PE." + "This entry represents a conceptual row in the mvpnGenericTable. + Each MVRF serviced by the PE will have an entry in this table. + The MVRF represented by this entry will have one or more + corresponding P-Multicast Service Interfaces (PMSIs) + and a corresponding VRF in MPLS-L3VPN-STD-MIB [RFC4382]. + " INDEX { mplsL3VpnVrfName, mvpnGenAddressFamily } - ::= { mvpnGeneralTable 1 } + ::= { mvpnGenericTable 1 } - MvpnGeneralEntry ::= SEQUENCE { + MvpnGenericEntry ::= SEQUENCE { mvpnGenAddressFamily INTEGER, - mvpnGenMvrfStatusChange INTEGER, - mvpnGenMvrfStatusChangeTime TimeStamp, + mvpnGenMvrfLastOperation INTEGER, + mvpnGenMvrfLastOperationTime TimeStamp, mvpnGenCmcastRouteProtocol INTEGER, - mvpnGenIpmsiConfig RowPointer, - mvpnGenInterAsPmsiConfig RowPointer, + mvpnGenIpmsiInfo RowPointer, + mvpnGenInterAsPmsiInfo RowPointer, mvpnGenUmhSelection INTEGER, - mvpnGenSiteType INTEGER, - mvpnGenSptnlLimit Unsigned32, - mvpnGenRowStatus RowStatus - + mvpnGenCustomerSiteType INTEGER, + mvpnGenSPTunnelLimit Unsigned32 } mvpnGenAddressFamily OBJECT-TYPE SYNTAX INTEGER { ipv4(1), ipv6(2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION - "The Address Family that this entry is for" - ::= { mvpnGeneralEntry 1 } + "The Address Family of the MVRF represented by this entry" + REFERENCE + "RFC6513, Section 1 + " + ::= { mvpnGenericEntry 1 } - mvpnGenMvrfStatusChange OBJECT-TYPE + mvpnGenMvrfLastOperation OBJECT-TYPE SYNTAX INTEGER { createdMvrf(1), deletedMvrf(2), modifiedMvrfIpmsiConfig(3), modifiedMvrfSpmsiConfig(4) } MAX-ACCESS read-only STATUS current DESCRIPTION - "This object describes the last status change that - happened for the given MVRF. + "This object describes the last operation pertaining + to the MVRF represented by this entry. createdMvrf(1): - indicates that the MVRF was created in the PE. + the MVRF was created in the PE. deletedMvrf(2): - indicates that the MVRF was deleted from the PE. + the MVRF was deleted from the PE. A row in this table will never have - mvpnGenMvrfStatusChange equal to deletedMvrf(2), + mvpnGenMvrfLastOperation equal to deletedMvrf(2), because in that case the row itself will be deleted from the table. - This value for mvpnGenMvrfStatusChange is defined mainly - for use in mvpnMvrfStatusChange notification. + This value for mvpnGenMvrfLastOperation is defined + mainly for use in mvpnMvrfOperationChange notification. modifiedMvrfIpmsiConfig(3): - indicates that the I-PMSI for the MVRF was configured, + an I-PMSI for the MVRF was configured, deleted or changed. modifiedMvrfSpmsiConfig(4): - indicates that the S-PMSI for the MVRF was configured, + an S-PMSI for the MVRF was configured, deleted or changed. " DEFVAL { createdMvrf } - ::= { mvpnGeneralEntry 2 } + ::= { mvpnGenericEntry 2 } - mvpnGenMvrfStatusChangeTime OBJECT-TYPE + mvpnGenMvrfLastOperationTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION - "The time at which the last status change for the MVRF in + "The time at which the last operation for the MVRF in question took place. The last operational change is specified - by mvpnGenMvrfStatusChange. + by mvpnGenMvrfLastOperation. + The time at which the last operation, specifed + in mvpnGenMvrfLastOperation, for the MVRF + represented by this entry was carried out. " - ::= { mvpnGeneralEntry 3 } + + ::= { mvpnGenericEntry 3 } mvpnGenCmcastRouteProtocol OBJECT-TYPE SYNTAX INTEGER { pim (1), bgp (2) } - MAX-ACCESS read-create + MAX-ACCESS read-only STATUS current DESCRIPTION - "The protocol used to signal C-multicast states across the - provider core. - pim(1): PIM (PIM-MVPN). - bgp(2): BGP (BGP-MVPN). + "The protocol used to signal C-multicast routing + information across the provider core. + PIM (PIM-MVPN): pim(1) + BGP (BGP-MVPN): bgp(2) " - ::= { mvpnGeneralEntry 4 } + REFERENCE + "RFC6513, Section 5" + ::= { mvpnGenericEntry 4 } - mvpnGenIpmsiConfig OBJECT-TYPE + mvpnGenIpmsiInfo OBJECT-TYPE SYNTAX RowPointer - MAX-ACCESS read-create + MAX-ACCESS read-only STATUS current DESCRIPTION - "This points to a row in mvpnPmsiConfigTable, - for I-PMSI configuration. + "This points to a conceptual row representing + the corresponding I-PMSI in mvpnPmsiTable. + If there is no I-PMSI for the MVRF, the + value of this object will be zeroDotZero. " - ::= { mvpnGeneralEntry 5 } + DEFVAL { zeroDotZero } + ::= { mvpnGenericEntry 5 } - mvpnGenInterAsPmsiConfig OBJECT-TYPE + mvpnGenInterAsPmsiInfo OBJECT-TYPE SYNTAX RowPointer - MAX-ACCESS read-create + MAX-ACCESS read-only STATUS current DESCRIPTION - "This points to a row in mvpnPmsiConfigTable, - for inter-as I-PMSI configuration, in case of segmented - inter-as provider tunnels. + "This points to a conceptual row representing + the corresponding Inter-AS I-PMSI in mvpnPmsiTable, + in case of segmented Inter-AS provider tunnels. + If there is no segmented Inter-AS I-PMSI for the MVRF, + the value of this object will be zeroDotZero. " - ::= { mvpnGeneralEntry 6 } + DEFVAL { zeroDotZero } + ::= { mvpnGenericEntry 6 } mvpnGenUmhSelection OBJECT-TYPE SYNTAX INTEGER { highestPeAddress (1), cRootGroupHashing (2), ucastUmhRoute (3) } - MAX-ACCESS read-create + MAX-ACCESS read-only STATUS current DESCRIPTION "The UMH selection method for this mvpn, as specified in section 5.1.3 of [RFC6513]: - highestPeAddress (1): PE with the highest address - cRootGroupHashing (2): hashing based on (c-root, c-group) - uncastUmhRoute (3): per ucast route towards c-root + PE with the highest address: highestPeAddress (1) + hashing based on (c-root, c-group): cRootGroupHashing (2) + per ucast route towards c-root: ucastUmhRoute (3) " - ::= { mvpnGeneralEntry 7 } + REFERENCE + "RFC6513, Section 5.1" + ::= { mvpnGenericEntry 7 } - mvpnGenSiteType OBJECT-TYPE + mvpnGenCustomerSiteType OBJECT-TYPE SYNTAX INTEGER { senderReceiver (1), receiverOnly (2), senderOnly (3) } - MAX-ACCESS read-create + MAX-ACCESS read-only STATUS current DESCRIPTION - "Whether this site is a receiver-only site or not. - senderReceiver (1): both sender and receiver site. - receiverOnly (2): receiver-only site. - senderOnly (3): sender-only site. + "The type of a customer site, which is connected to + this PE, in the MVPN which has the MVRF represented + by this entry. + + Site is both sender and receiver: senderReceiver (1) + Site is receiver-only : receiverOnly (2) + Site is sender-only : senderOnly (3) " - ::= { mvpnGeneralEntry 8 } + REFERENCE + "RFC6513, Section 2.3" + ::= { mvpnGenericEntry 8 } - mvpnGenSptnlLimit OBJECT-TYPE + mvpnGenSPTunnelLimit OBJECT-TYPE SYNTAX Unsigned32 - MAX-ACCESS read-create + MAX-ACCESS read-only STATUS current DESCRIPTION - "The max number of selective provider tunnels this PE - allows for this mvpn." - ::= { mvpnGeneralEntry 9 } + "The maximum number of selective provider tunnels that + this PE allows for this MVPN. + " + REFERENCE + "RFC6513, Section 13" - mvpnGenRowStatus OBJECT-TYPE - SYNTAX RowStatus - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "This is used to create or delete a row in this table." - ::= { mvpnGeneralEntry 10 } + ::= { mvpnGenericEntry 9 } - -- General BGP-MVPN table + -- Generic BGP-MVPN table - mvpnBgpGeneralTable OBJECT-TYPE - SYNTAX SEQUENCE OF MvpnBgpGeneralEntry + mvpnBgpGenericTable OBJECT-TYPE + SYNTAX SEQUENCE OF MvpnBgpGenericEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION - "This table augments the mvpnGeneralTable and is for BGP-MVPN - specific information. + "This table specifies the specific information of MVRFs of MVPNs + that use BGP for exchanging C-Multicast routing information + present in this PE. " - ::= { mvpnGeneral 2 } + ::= { mvpnGeneric 2 } - mvpnBgpGeneralEntry OBJECT-TYPE - SYNTAX MvpnBgpGeneralEntry + mvpnBgpGenericEntry OBJECT-TYPE + SYNTAX MvpnBgpGenericEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION - "The mvpnBgpGeneralEntry matches and augments an - mvpnGeneralEntry for a BGP-MVPN instance, with BGP-MVPN - specific informatoin. + "This entry represents a conceptual row in the mvpnBgpGenericTable. + Each MVRF of an MVPN that use BGP for exchanging C-Multicast + routing information will have an entry in this table. + The MVRF represented by this entry will have + a corresponding entry in the mvpnGenericTable. " - AUGMENTS { mvpnGeneralEntry } - ::= { mvpnBgpGeneralTable 1 } + INDEX { + mplsL3VpnVrfName, + mvpnGenAddressFamily + } + ::= { mvpnBgpGenericTable 1 } - MvpnBgpGeneralEntry ::= SEQUENCE { + MvpnBgpGenericEntry ::= SEQUENCE { mvpnBgpGenMode INTEGER, - mvpnBgpGenVrfRtImport MplsL3VpnRouteDistinguisher, - mvpnBgpGenSrcAs InetAutonomousSystemNumber + mvpnBgpGenVrfRouteImport MplsL3VpnRouteDistinguisher, + mvpnBgpGenSrcAs InetAutonomousSystemNumber, + mvpnBgpGenCmcastRouteWithdrawalTimer Unsigned32, + mvpnBgpGenSrcSharedTreeJoinTimer Unsigned32, + mvpnBgpGenMsgRateLimit Unsigned32, + mvpnBgpGenMaxSpmsiAdRoutes Unsigned32, + mvpnBgpGenMaxSpmsiAdRouteFreq Unsigned32, + mvpnBgpGenMaxSrcActiveAdRoutes Unsigned32, + mvpnBgpGenMaxSrcActiveAdRouteFreq Unsigned32 } mvpnBgpGenMode OBJECT-TYPE SYNTAX INTEGER { rptSpt (1), sptOnly (2) } - MAX-ACCESS read-write + MAX-ACCESS read-only STATUS current DESCRIPTION "For two different BGP-MVPN modes: rptSpt(1): inter-site shared tree mode sptOnly(2): inter-site source-only tree mode. " - ::= { mvpnBgpGeneralEntry 1} + REFERENCE + "RFC6513, Section 9.3.1" + ::= { mvpnBgpGenericEntry 1 } - mvpnBgpGenVrfRtImport OBJECT-TYPE + mvpnBgpGenVrfRouteImport OBJECT-TYPE SYNTAX MplsL3VpnRouteDistinguisher - MAX-ACCESS read-write + MAX-ACCESS read-only STATUS current DESCRIPTION "The VRF Route Import Extended Community that this PE - adds to unicast vpn routes that it advertises for this mvpn. + adds to unicast VPN routes that it advertises for this MVPN. " REFERENCE - "RFC4364, Section 4.2 - RFC4382, Section 7 + "RFC6514, Section 7 " - ::= { mvpnBgpGeneralEntry 2} + ::= { mvpnBgpGenericEntry 2 } mvpnBgpGenSrcAs OBJECT-TYPE SYNTAX InetAutonomousSystemNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The Source AS number in Source AS Extended Community that this - PE adds to the unicast vpn routes that it advertises for - this mvpn. + PE adds to the unicast VPN routes that it advertises for + this MVPN. " - ::= { mvpnBgpGeneralEntry 3} + REFERENCE + "RFC6514, Section 6 + " + ::= { mvpnBgpGenericEntry 3 } - -- PMSI Configuration Table + mvpnBgpGenCmcastRouteWithdrawalTimer OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The configurable timer to control the delay + for the advertisement of withdrawals of + C-multicast routes. - mvpnPmsiConfigTable OBJECT-TYPE - SYNTAX SEQUENCE OF MvpnPmsiConfigEntry - MAX-ACCESS not-accessible + " + REFERENCE + "RFC6514, Section 16.1.1" + ::= { mvpnBgpGenericEntry 4 } + + mvpnBgpGenSrcSharedTreeJoinTimer OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-write STATUS current DESCRIPTION - "This table specifies the configured PMSIs." - ::= { mvpnConfig 1 } + "The configurable timer to control the delay + for the advertisement of Source/Shared Tree Join + C-multicast routes. + " + REFERENCE + "RFC6514, Section 16.1.2" + ::= { mvpnBgpGenericEntry 5 } - mvpnPmsiConfigEntry OBJECT-TYPE - SYNTAX MvpnPmsiConfigEntry - MAX-ACCESS not-accessible + mvpnBgpGenMsgRateLimit OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-write STATUS current DESCRIPTION - "An entry in this table is created for each PMSI configured - on this router. It can be referred to by either I-PMSI - configuration (in mvpnGeneralEntry) or S-PMSI configuration - (in mvpnSpmsiConfigEntry) + "The upper bounds on rate of BGP message exchange among PEs + for exchanging C-multicast routing information " - INDEX { - mvpnPmsiConfigTunnelType, - mvpnPmsiConfigTunnelAuxInfo, - mvpnPmsiConfigTunnelPimGroupAddrType, - mvpnPmsiConfigTunnelPimGroupAddr, - mvpnPmsiConfigTunnelOrTemplateName - } + REFERENCE + "RFC6514, Section 17" + ::= { mvpnBgpGenericEntry 6 } - ::= { mvpnPmsiConfigTable 1 } + mvpnBgpGenMaxSpmsiAdRoutes OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The upper bound on the number of S-PMSI A-D routes. + " + REFERENCE + "RFC6514, Section 17" + ::= { mvpnBgpGenericEntry 7 } - MvpnPmsiConfigEntry ::= SEQUENCE { - mvpnPmsiConfigTunnelType - L2L3VpnMcastProviderTunnelType, - mvpnPmsiConfigTunnelAuxInfo Unsigned32, - mvpnPmsiConfigTunnelPimGroupAddrType - InetAddressType, - mvpnPmsiConfigTunnelPimGroupAddr - InetAddress, - mvpnPmsiConfigTunnelOrTemplateName - SnmpAdminString, - mvpnPmsiConfigEncapsType INTEGER, - mvpnPmsiConfigRowStatus RowStatus - } + mvpnBgpGenMaxSpmsiAdRouteFreq OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The upper bound on how frequently S-PMSI A-D routes + may be generated. - mvpnPmsiConfigTunnelType OBJECT-TYPE - SYNTAX L2L3VpnMcastProviderTunnelType - MAX-ACCESS not-accessible + " + REFERENCE + "RFC6514, Section 17" + ::= { mvpnBgpGenericEntry 8 } + + mvpnBgpGenMaxSrcActiveAdRoutes OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-write STATUS current DESCRIPTION - "Type of tunnel used to instantiate the PMSI." - ::= { mvpnPmsiConfigEntry 1 } + "The upper bound on the number of Source Active A-D routes. + " + REFERENCE + "RFC6514, Section 17" + ::= { mvpnBgpGenericEntry 9 } - mvpnPmsiConfigTunnelAuxInfo OBJECT-TYPE + mvpnBgpGenMaxSrcActiveAdRouteFreq OBJECT-TYPE SYNTAX Unsigned32 - MAX-ACCESS not-accessible + MAX-ACCESS read-write STATUS current DESCRIPTION - "Additional tunnel information depending on the value of - mvpnPmsiConfigTunnelType object. + "The upper bound on how frequently Source Active A-D routes + may be generated. + " + REFERENCE + "RFC6514, Section 17" + ::= { mvpnBgpGenericEntry 10 } - pimSsm(3), pimAsm(4), pimBidir(5): - In case of S-PMSI, number of groups starting at - mvpnPmsiConfigTunnelPimGroupAddress. - This allows a range of PIM provider tunnel - group addresses to be specified in S-PMSI case. - In I-PMSI case, it must be 1. + -- PMSI Configuration Table - rsvpP2mp(1): - 1 for statically specified rsvp-p2mp tunnel - 2 for dynamically created rsvp-p2mp tunnel + mvpnPmsiTable OBJECT-TYPE + SYNTAX SEQUENCE OF MvpnPmsiEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry in this table corresponds to + the attribute information of a specific + PMSI configured on a PE router. + " + ::= { mvpnConfig 1 } + + mvpnPmsiEntry OBJECT-TYPE + SYNTAX MvpnPmsiEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A conceptual row corresponding to a specific + PMSI on this router. - ingressReplication(6): - 1 for using any existing p2p/mp2p LSP - 2 for dynamically creating new p2p LSP " + INDEX { + mvpnPmsiTunnelIfIndex + } + ::= { mvpnPmsiTable 1 } - ::= { mvpnPmsiConfigEntry 2 } + MvpnPmsiEntry ::= SEQUENCE { + mvpnPmsiTunnelIfIndex InterfaceIndex, + mvpnPmsiTunnelType L2L3VpnMcastProviderTunnelType, + mvpnPmsiTunnelPimGroupAddrType InetAddressType, + mvpnPmsiTunnelPimGroupAddr InetAddress, + mvpnPmsiEncapsulationType INTEGER + } - mvpnPmsiConfigTunnelPimGroupAddrType OBJECT-TYPE - SYNTAX InetAddressType + mvpnPmsiTunnelIfIndex OBJECT-TYPE + SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION - "In case of PIM provider tunnel, the type of tunnel address." - ::= { mvpnPmsiConfigEntry 3 } + "This is a unique index for an entry in the + mvpnPmsiTable. A non-zero index for an + entry indicates the ifIndex for the corresponding + entry of PMSI in the ifTable. + " + REFERENCE + "RFC2863 + " + ::= { mvpnPmsiEntry 1 } - mvpnPmsiConfigTunnelPimGroupAddr OBJECT-TYPE - SYNTAX InetAddress + mvpnPmsiTunnelType OBJECT-TYPE + SYNTAX L2L3VpnMcastProviderTunnelType MAX-ACCESS not-accessible STATUS current DESCRIPTION - "In case of PIM provider tunnel, the provider tunnel address." - ::= { mvpnPmsiConfigEntry 4 } + "This object indicates the type of tunnel used to + instantiate the PMSI corresponding to this entry" + REFERENCE + "RFC6513 Sec. 2.6 + " + ::= { mvpnPmsiEntry 2 } - mvpnPmsiConfigTunnelOrTemplateName OBJECT-TYPE - SYNTAX SnmpAdminString + mvpnPmsiTunnelPimGroupAddrType OBJECT-TYPE + SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION - "The tunnel name or template name used to create tunnels. - The value of this object depends on the values of - mvpnPmsiConfigTunnelType and mvpnPmsiConfigTunnelAuxInfo - objects: + "When the PIM provider tunnel is used for instantiating + the PMSI corresponding to this entry, i.e., + the value of mvpnPmsiTunnelType is + pimSsm(3), pimAsm(4), or pimBidir(5), + this object indicates the type of tunnel address. + Otherwise, the value of this object will be + unknown(0). + " + ::= { mvpnPmsiEntry 3 } - dynamically created rsvp-p2mp tunnel: template name - statically specified rsvp-p2mp tunnel: tunnel name - ingress-replication using - dynamically created LSPs: template name - other: null + mvpnPmsiTunnelPimGroupAddr OBJECT-TYPE + SYNTAX InetAddress + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "When the PIM provider tunnel is used for instantiating + the PMSI corresponding to this entry, i.e., + the value of mvpnPmsiTunnelType is + pimSsm(3), pimAsm(4), or pimBidir(5), + this object indicates the tunnel address. + Otherwise, the value of this object will be + a string of length zero. " - ::= { mvpnPmsiConfigEntry 5 } + ::= { mvpnPmsiEntry 4 } - mvpnPmsiConfigEncapsType OBJECT-TYPE + mvpnPmsiEncapsulationType OBJECT-TYPE SYNTAX INTEGER { greIp (1), ipIp (2), mpls (3) } - MAX-ACCESS read-create + MAX-ACCESS read-only STATUS current DESCRIPTION - "The encapsulation type to be used, in case of PIM tunnel or - ingress-replication. - " + "The encapsulation type to be used for sending + packets through a P-tunnel. - ::= { mvpnPmsiConfigEntry 6 } + The enumerated values and the corresponding + encapsulation types are as follows: - mvpnPmsiConfigRowStatus OBJECT-TYPE - SYNTAX RowStatus - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "Used to create/modify/delete a row in this table." - ::= { mvpnPmsiConfigEntry 7 } + greIp (0) : GRE (Generic Routing Encapsulation) encapsulation [RFC2784] + ipIp (1) : IP-in-IP encapsulation [RFC2003] + mpls (2) : MPLS encapsulation [RFC3032] + " + REFERENCE + "RFC2003 + RFC2784 + RFC3032 + RFC6513 Sec. 12.1 + " + + ::= { mvpnPmsiEntry 5 } -- S-PMSI configuration table - mvpnSpmsiConfigTable OBJECT-TYPE - SYNTAX SEQUENCE OF MvpnSpmsiConfigEntry + mvpnSpmsiTable OBJECT-TYPE + SYNTAX SEQUENCE OF MvpnSpmsiEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION - "This table specifies S-PMSI configuration." + "An entry in this table corresponds to + a specific S-PMSI configured on a PE router. + This table stores only S-PMSI specific + attribute information and generic attribute + information of the S-PMSI is stored in + mvpnPmsiTable. + Therefore, there MUST be corresponding entry + that pertains to the S-PMSI, in mvpnPmsiTable. + " ::= { mvpnConfig 2 } - mvpnSpmsiConfigEntry OBJECT-TYPE - SYNTAX MvpnSpmsiConfigEntry + mvpnSpmsiEntry OBJECT-TYPE + SYNTAX MvpnSpmsiEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION - "An entry is created for each S-PMSI configuration." + "A conceptual row corresponding to a specific + S-PMSI on this router. + + Implementers need to be aware that there are quite a few + index objects that together can exceed the size allowed + for an Object Identifier (OID). So implementers must make + sure that OIDs of column instances in this table will have + no more than 128 sub-identifiers, otherwise they cannot be + accessed using SNMPv1, SNMPv2c, or SNMPv3. + " INDEX { mplsL3VpnVrfName, - mvpnSpmsiConfigCmcastAddrType, - mvpnSpmsiConfigCmcastGroupAddr, - mvpnSpmsiConfigCmcastGroupPrefixLen, - mvpnSpmsiConfigCmcastSourceAddr, - mvpnSpmsiConfigCmcastSourcePrefixLen + mvpnSpmsiCmcastAddrType, + mvpnSpmsiCmcastGroupAddr, + mvpnSpmsiCmcastGroupPrefixLen, + mvpnSpmsiCmcastSourceAddr, + mvpnSpmsiCmcastSourcePrefixLen } - ::= { mvpnSpmsiConfigTable 1 } + ::= { mvpnSpmsiTable 1 } - MvpnSpmsiConfigEntry ::= SEQUENCE { - mvpnSpmsiConfigCmcastAddrType InetAddressType, - mvpnSpmsiConfigCmcastGroupAddr InetAddress, - mvpnSpmsiConfigCmcastGroupPrefixLen InetAddressPrefixLength, - mvpnSpmsiConfigCmcastSourceAddr InetAddress, - mvpnSpmsiConfigCmcastSourcePrefixLen InetAddressPrefixLength, - mvpnSpmsiConfigThreshold Unsigned32, - mvpnSpmsiConfigPmsiPointer RowPointer, - mvpnSpmsiConfigRowStatus RowStatus + MvpnSpmsiEntry ::= SEQUENCE { + mvpnSpmsiCmcastAddrType InetAddressType, + mvpnSpmsiCmcastGroupAddr InetAddress, + mvpnSpmsiCmcastGroupPrefixLen InetAddressPrefixLength, + mvpnSpmsiCmcastSourceAddr InetAddress, + mvpnSpmsiCmcastSourcePrefixLen InetAddressPrefixLength, + mvpnSpmsiThreshold Unsigned32, + mvpnSpmsiPmsiPointer RowPointer } - mvpnSpmsiConfigCmcastAddrType OBJECT-TYPE + mvpnSpmsiCmcastAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION - "Type of C-multicast address" - ::= { mvpnSpmsiConfigEntry 1 } + "Type of C-multicast source and group addresses of + a particular C-flow which is assigned to an S-PMSI + corresponding to this entry." + ::= { mvpnSpmsiEntry 1 } - mvpnSpmsiConfigCmcastGroupAddr OBJECT-TYPE + mvpnSpmsiCmcastGroupAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION - "C-multicast group address" - ::= { mvpnSpmsiConfigEntry 2 } + "A group address of a particular C-flow which is + assigned to an S-PMSI corresponding to this entry." + ::= { mvpnSpmsiEntry 2 } - mvpnSpmsiConfigCmcastGroupPrefixLen OBJECT-TYPE + mvpnSpmsiCmcastGroupPrefixLen OBJECT-TYPE SYNTAX InetAddressPrefixLength MAX-ACCESS not-accessible STATUS current DESCRIPTION - "C-multicast group address prefix length. + "A prefix length of mvpnSpmsiCmcastGroupAddr. A group 0 (or ::0) with prefix length 32 (or 128) indicates wildcard group, while a group 0 (or ::0) with prefix length 0 indicates any group. " - ::= { mvpnSpmsiConfigEntry 3 } + ::= { mvpnSpmsiEntry 3 } - mvpnSpmsiConfigCmcastSourceAddr OBJECT-TYPE + mvpnSpmsiCmcastSourceAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION - "C-multicast source address" - ::= { mvpnSpmsiConfigEntry 4 } + "A source address of a particular C-flow which is + assigned to an S-PMSI corresponding to this entry." + ::= { mvpnSpmsiEntry 4 } - mvpnSpmsiConfigCmcastSourcePrefixLen OBJECT-TYPE + mvpnSpmsiCmcastSourcePrefixLen OBJECT-TYPE SYNTAX InetAddressPrefixLength MAX-ACCESS not-accessible STATUS current DESCRIPTION - "C-multicast source address prefix length. + "A prefix length of mvpnSpmsiCmcastSourceAddr. A source 0 (or ::0) with prefix length 32 (or 128) indicates a wildcard source, while a source 0 (or ::0) with prefix length 0 indicates any source. " - ::= { mvpnSpmsiConfigEntry 5 } + ::= { mvpnSpmsiEntry 5 } - mvpnSpmsiConfigThreshold OBJECT-TYPE + mvpnSpmsiThreshold OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) UNITS "kilobits per second" - MAX-ACCESS read-create + MAX-ACCESS read-write STATUS current DESCRIPTION "The bandwidth threshold value which when exceeded for a multicast routing entry in the given MVRF, triggers usage of S-PMSI. " - ::= { mvpnSpmsiConfigEntry 6 } + REFERENCE + "RFC6513 Sec. 7.2" + ::= { mvpnSpmsiEntry 6 } - mvpnSpmsiConfigPmsiPointer OBJECT-TYPE + mvpnSpmsiPmsiPointer OBJECT-TYPE SYNTAX RowPointer - MAX-ACCESS read-create + MAX-ACCESS read-only STATUS current DESCRIPTION - "This points to a row in mvpnPmsiConfigTable, + "This points to a row in mvpnPmsiTable, to specify tunnel attributes. " - ::= { mvpnSpmsiConfigEntry 7 } - - mvpnSpmsiConfigRowStatus OBJECT-TYPE - SYNTAX RowStatus - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "Used to create/modify/delete a row in this table." - ::= { mvpnSpmsiConfigEntry 8 } + ::= { mvpnSpmsiEntry 7 } -- Table of intra-as I-PMSIs advertised/received - mvpnIpmsiTable OBJECT-TYPE - SYNTAX SEQUENCE OF MvpnIpmsiEntry + mvpnIpmsiAdvtTable OBJECT-TYPE + SYNTAX SEQUENCE OF MvpnIpmsiAdvtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is for all advertised/received I-PMSI advertisements. " ::= { mvpnStates 1 } - mvpnIpmsiEntry OBJECT-TYPE - SYNTAX MvpnIpmsiEntry + mvpnIpmsiAdvtEntry OBJECT-TYPE + SYNTAX MvpnIpmsiAdvtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table corresponds to an I-PMSI - advertisement that is advertised/received on this router. - + advertisement that is advertised/received by this router. This represents all the sender PEs in the MVPN, with the provider tunnel they use to send traffic. + + Implementers need to be aware that there are quite a few + index objects that together can exceed the size allowed + for an Object Identifier (OID). So implementers must make + sure that OIDs of column instances in this table will have + no more than 128 sub-identifiers, otherwise they cannot be + accessed using SNMPv1, SNMPv2c, or SNMPv3. " INDEX { mplsL3VpnVrfName, - mvpnIpmsiAfi, - mvpnIpmsiRD, - mvpnIpmsiOrigAddrType, - mvpnIpmsiOrigAddr + mvpnIpmsiAdvtAfi, + mvpnIpmsiAdvtRD, + mvpnIpmsiAdvtOrigAddrType, + mvpnIpmsiAdvtOrigAddr } - ::= { mvpnIpmsiTable 1 } + ::= { mvpnIpmsiAdvtTable 1 } - MvpnIpmsiEntry ::= SEQUENCE { - mvpnIpmsiAfi INTEGER, - mvpnIpmsiRD MplsL3VpnRouteDistinguisher, - mvpnIpmsiOrigAddrType InetAddressType, - mvpnIpmsiOrigAddr InetAddress, - mvpnIpmsiUpTime TimeInterval, - mvpnIpmsiAttribute RowPointer + MvpnIpmsiAdvtEntry ::= SEQUENCE { + mvpnIpmsiAdvtAfi INTEGER, + mvpnIpmsiAdvtRD MplsL3VpnRouteDistinguisher, + mvpnIpmsiAdvtOrigAddrType InetAddressType, + mvpnIpmsiAdvtOrigAddr InetAddress, + mvpnIpmsiAdvtTunnelAttribute RowPointer, + mvpnIpmsiAdvtReceived Counter32, + mvpnIpmsiAdvtReceivedError Counter32, + mvpnIpmsiAdvtMalformedTunnelType Counter32, + mvpnIpmsiAdvtMalformedTunnelId Counter32, + mvpnIpmsiAdvtLastReceivedTime TimeStamp, + mvpnIpmsiAdvtCounterDiscontinuityTime TimeStamp } - mvpnIpmsiAfi OBJECT-TYPE + mvpnIpmsiAdvtAfi OBJECT-TYPE SYNTAX INTEGER { ipv4(1), ipv6(2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "The address family this I-PMSI is for." - ::= { mvpnIpmsiEntry 1 } - mvpnIpmsiRD OBJECT-TYPE + ::= { mvpnIpmsiAdvtEntry 1 } + + mvpnIpmsiAdvtRD OBJECT-TYPE SYNTAX MplsL3VpnRouteDistinguisher MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Route Distinguisher in this I-PMSI." - ::= { mvpnIpmsiEntry 2 } + ::= { mvpnIpmsiAdvtEntry 2 } - mvpnIpmsiOrigAddrType OBJECT-TYPE + mvpnIpmsiAdvtOrigAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION - "The Internet address type of mvpnIpmsiOrigAddr." - ::= { mvpnIpmsiEntry 3 } + "The Internet address type of mvpnIpmsiAdvtOrigAddr." + ::= { mvpnIpmsiAdvtEntry 3 } - mvpnIpmsiOrigAddr OBJECT-TYPE + mvpnIpmsiAdvtOrigAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The BGP address of the PE that originated the I-PMSI." - ::= { mvpnIpmsiEntry 4 } + ::= { mvpnIpmsiAdvtEntry 4 } - mvpnIpmsiUpTime OBJECT-TYPE - SYNTAX TimeInterval + mvpnIpmsiAdvtTunnelAttribute OBJECT-TYPE + SYNTAX RowPointer MAX-ACCESS read-only STATUS current DESCRIPTION - "The time since this I-PMSI - was first advertised/received by the PE. + "Points to a row in the l2L3VpnMcastPmsiTunnelAttributeTable." + ::= { mvpnIpmsiAdvtEntry 5 } + + mvpnIpmsiAdvtReceived OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of I-PMSI advertisements received by the PE router. + This includes advertisements that were discarded. + Discontinuities in the value of this counter can + occur at re-initialization of the management system, + and at other times as indicated by the value of + mvpnIpmsiAdvtCounterDiscontinuityTime. " - ::= { mvpnIpmsiEntry 5 } + ::= { mvpnIpmsiAdvtEntry 6 } - mvpnIpmsiAttribute OBJECT-TYPE - SYNTAX RowPointer + mvpnIpmsiAdvtReceivedError OBJECT-TYPE + SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION - "Points to a row in the l2L3VpnMcastPmsiTunnelAttributeTable." - ::= { mvpnIpmsiEntry 6 } + "The total number of errors in the I-PMSI advertisements + received by the PE router. + The value of this object is the sum of + the values of mvpnIpmsiAdvtMalformedTunnelType and + mvpnIpmsiAdvtMalformedTunnelId. + Discontinuities in the value of this counter can + occur at re-initialization of the management system, + and at other times as indicated by the value of + mvpnIpmsiAdvtCounterDiscontinuityTime. + " + ::= { mvpnIpmsiAdvtEntry 7 } + + mvpnIpmsiAdvtMalformedTunnelType OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of received I-PMSI advertisements that + contain a PMSI Tunnel attribute whose Tunnel + Type field has an undefined tunnel type. + Discontinuities in the value of this counter can + occur at re-initialization of the management system, + and at other times as indicated by the value of + mvpnIpmsiAdvtCounterDiscontinuityTime. + " + REFERENCE + "RFC6514 Sec.5" + ::= { mvpnIpmsiAdvtEntry 8 } + + mvpnIpmsiAdvtMalformedTunnelId OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of received I-PMSI advertisements that + contain a PMSI Tunnel attribute whose Tunnel + Identifier field cannot be parsed as a + tunnel identifier of the tunnel types specified in + the Tunnel type field of the attribute. + Discontinuities in the value of this counter can + occur at re-initialization of the management system, + and at other times as indicated by the value of + mvpnIpmsiAdvtCounterDiscontinuityTime. + + " + REFERENCE + "RFC6514 Sec.5" + ::= { mvpnIpmsiAdvtEntry 9 } + + mvpnIpmsiAdvtLastReceivedTime OBJECT-TYPE + SYNTAX TimeStamp + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value of sysUpTime when the last I-PMSI + advertisement was received by the PE router. + " + ::= { mvpnIpmsiAdvtEntry 10 } + + mvpnIpmsiAdvtCounterDiscontinuityTime OBJECT-TYPE + SYNTAX TimeStamp + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value of sysUpTime on the most recent occasion + at which any one or more of this syslog application's + counters, viz., counters with OID prefix + 'mvpnIpmsiAdvtReceived' or + 'mvpnIpmsiAdvtReceivedError' or + 'mvpnIpmsiAdvtMalformedTunnelType' or + 'mvpnIpmsiAdvtMalformedTunnelId' suffered a + discontinuity. + If no such discontinuities have occurred since the + last re-initialization of the local management + subsystem, then this object will have a zero value. + " + ::= { mvpnIpmsiAdvtEntry 11 } -- Table of inter-as I-PMSIs advertised/received - mvpnInterAsIpmsiTable OBJECT-TYPE - SYNTAX SEQUENCE OF MvpnInterAsIpmsiEntry + mvpnInterAsIpmsiAdvtTable OBJECT-TYPE + SYNTAX SEQUENCE OF MvpnInterAsIpmsiAdvtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is for all advertised/received inter-as I-PMSI advertisements." ::= { mvpnStates 2 } - mvpnInterAsIpmsiEntry OBJECT-TYPE - SYNTAX MvpnInterAsIpmsiEntry + mvpnInterAsIpmsiAdvtEntry OBJECT-TYPE + SYNTAX MvpnInterAsIpmsiAdvtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table corresponds to an inter-as I-PMSI - advertisement that is advertised/received on this router. + advertisement that is advertised/received by this router. This represents all the ASes in the MVPN, with the provider tunnel used to send traffic to. + + Implementers need to be aware that there are quite a few + index objects that together can exceed the size allowed + for an Object Identifier (OID). So implementers must make + sure that OIDs of column instances in this table will have + no more than 128 sub-identifiers, otherwise they cannot be + accessed using SNMPv1, SNMPv2c, or SNMPv3. " INDEX { mplsL3VpnVrfName, - mvpnInterAsIpmsiAfi, - mvpnInterAsIpmsiRD, - mvpnInterAsIpmsiSrcAs + mvpnInterAsIpmsiAdvtAfi, + mvpnInterAsIpmsiAdvtRD, + mvpnInterAsIpmsiAdvtSrcAs } - ::= { mvpnInterAsIpmsiTable 1 } + ::= { mvpnInterAsIpmsiAdvtTable 1 } - MvpnInterAsIpmsiEntry ::= SEQUENCE { - mvpnInterAsIpmsiAfi INTEGER, - mvpnInterAsIpmsiRD MplsL3VpnRouteDistinguisher, - mvpnInterAsIpmsiSrcAs InetAutonomousSystemNumber, - mvpnInterAsIpmsiAttribute RowPointer + MvpnInterAsIpmsiAdvtEntry ::= SEQUENCE { + mvpnInterAsIpmsiAdvtAfi INTEGER, + mvpnInterAsIpmsiAdvtRD MplsL3VpnRouteDistinguisher, + mvpnInterAsIpmsiAdvtSrcAs InetAutonomousSystemNumber, + mvpnInterAsIpmsiAdvtTunnelAttribute RowPointer, + mvpnInterAsIpmsiAdvtReceived Counter32, + mvpnInterAsIpmsiAdvtReceivedError Counter32, + mvpnInterAsIpmsiAdvtMalformedTunnelType Counter32, + mvpnInterAsIpmsiAdvtMalformedTunnelId Counter32, + mvpnInterAsIpmsiAdvtLastReceivedTime TimeStamp, + mvpnInterAsIpmsiAdvtCounterDiscontinuityTime TimeStamp } - mvpnInterAsIpmsiAfi OBJECT-TYPE + mvpnInterAsIpmsiAdvtAfi OBJECT-TYPE SYNTAX INTEGER { ipv4(1), ipv6(2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "The address family this I-PMSI is for." - ::= { mvpnInterAsIpmsiEntry 1 } + ::= { mvpnInterAsIpmsiAdvtEntry 1 } - mvpnInterAsIpmsiRD OBJECT-TYPE + mvpnInterAsIpmsiAdvtRD OBJECT-TYPE SYNTAX MplsL3VpnRouteDistinguisher MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Route Distinguisher in this inter-as I-PMSI." - ::= { mvpnInterAsIpmsiEntry 2 } + ::= { mvpnInterAsIpmsiAdvtEntry 2 } - mvpnInterAsIpmsiSrcAs OBJECT-TYPE + mvpnInterAsIpmsiAdvtSrcAs OBJECT-TYPE SYNTAX InetAutonomousSystemNumber MAX-ACCESS not-accessible STATUS current DESCRIPTION "The source-as in this inter-as I-PMSI." - ::= { mvpnInterAsIpmsiEntry 3 } + ::= { mvpnInterAsIpmsiAdvtEntry 3 } - mvpnInterAsIpmsiAttribute OBJECT-TYPE + mvpnInterAsIpmsiAdvtTunnelAttribute OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-only STATUS current DESCRIPTION "Points to a row in the l2L3VpnMcastPmsiTunnelAttributeTable." - ::= { mvpnInterAsIpmsiEntry 4 } + ::= { mvpnInterAsIpmsiAdvtEntry 4 } + + mvpnInterAsIpmsiAdvtReceived OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of Inter-AS I-PMSI advertisements received + by the PE router. + This includes advertisements that were discarded. + Discontinuities in the value of this counter can + occur at re-initialization of the management system, + and at other times as indicated by the value of + mvpnInterAsIpmsiAdvtCounterDiscontinuityTime. + " + ::= { mvpnInterAsIpmsiAdvtEntry 5 } + + mvpnInterAsIpmsiAdvtReceivedError OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The total number of errors in the Inter-AS I-PMSI + advertisements received by the PE router. + The value of this object is the sum of + the values of mvpnInterAsIpmsiAdvtMalformedTunnelType and + mvpnInterAsIpmsiAdvtMalformedTunnelId. + Discontinuities in the value of this counter can + occur at re-initialization of the management system, + and at other times as indicated by the value of + mvpnInterAsIpmsiAdvtCounterDiscontinuityTime. + " + ::= { mvpnInterAsIpmsiAdvtEntry 6 } + + mvpnInterAsIpmsiAdvtMalformedTunnelType OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of received Inter-AS I-PMSI advertisements that + contain a PMSI Tunnel attribute whose Tunnel + Type field has an undefined tunnel type. + Discontinuities in the value of this counter can + occur at re-initialization of the management system, + and at other times as indicated by the value of + mvpnInterAsIpmsiAdvtCounterDiscontinuityTime. + " + REFERENCE + "RFC6514 Sec.5" + ::= { mvpnInterAsIpmsiAdvtEntry 7 } + + mvpnInterAsIpmsiAdvtMalformedTunnelId OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of received Inter-AS I-PMSI advertisements that + contain a PMSI Tunnel attribute whose Tunnel + Identifier field cannot be parsed as a + tunnel identifier of the tunnel types specified in + the Tunnel type field of the attribute. + Discontinuities in the value of this counter can + occur at re-initialization of the management system, + and at other times as indicated by the value of + mvpnInterAsIpmsiAdvtCounterDiscontinuityTime. + " + REFERENCE + "RFC6514 Sec.5" + ::= { mvpnInterAsIpmsiAdvtEntry 8 } + + mvpnInterAsIpmsiAdvtLastReceivedTime OBJECT-TYPE + SYNTAX TimeStamp + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value of sysUpTime when the last Inter-AS I-PMSI + advertisement was received by the PE router. + " + ::= { mvpnInterAsIpmsiAdvtEntry 9 } + + mvpnInterAsIpmsiAdvtCounterDiscontinuityTime OBJECT-TYPE + SYNTAX TimeStamp + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value of sysUpTime on the most recent occasion + at which any one or more of this syslog application's + counters, viz., counters with OID prefix + 'mvpnInterAsIpmsiAdvtReceived' or + 'mvpnInterAsIpmsiAdvtReceivedError' or + 'mvpnInterAsIpmsiAdvtMalformedTunnelType' or + 'mvpnInterAsIpmsiAdvtMalformedTunnelId' suffered a + discontinuity. + If no such discontinuities have occurred since the + last re-initialization of the local management + subsystem, then this object will have a zero value. + " + ::= { mvpnInterAsIpmsiAdvtEntry 10 } -- Table of S-PMSIs advertised/received - mvpnSpmsiTable OBJECT-TYPE - SYNTAX SEQUENCE OF MvpnSpmsiEntry + mvpnSpmsiAdvtTable OBJECT-TYPE + SYNTAX SEQUENCE OF MvpnSpmsiAdvtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table has information about the S-PMSIs sent/received by a PE. " ::= { mvpnStates 3 } - mvpnSpmsiEntry OBJECT-TYPE - SYNTAX MvpnSpmsiEntry + mvpnSpmsiAdvtEntry OBJECT-TYPE + SYNTAX MvpnSpmsiAdvtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table is created or updated for each S-PMSI advertised/received in a particular MVRF. + + Implementers need to be aware that there are quite a few + index objects that together can exceed the size allowed + for an Object Identifier (OID). So implementers must make + sure that OIDs of column instances in this table will have + no more than 128 sub-identifiers, otherwise they cannot be + accessed using SNMPv1, SNMPv2c, or SNMPv3. " INDEX { mplsL3VpnVrfName, - mvpnSpmsiCmcastAddrType, - mvpnSpmsiCmcastGroupAddr, - mvpnSpmsiCmcastGroupPrefixLen, - mvpnSpmsiCmcastSourceAddr, - mvpnSpmsiCmcastSourcePrefixLen, - mvpnSpmsiOrigAddrType, - mvpnSpmsiOrigAddr + mvpnSpmsiAdvtCmcastAddrType, + mvpnSpmsiAdvtCmcastGroupAddr, + mvpnSpmsiAdvtCmcastGroupPrefixLen, + mvpnSpmsiAdvtCmcastSourceAddr, + mvpnSpmsiAdvtCmcastSourcePrefixLen, + mvpnSpmsiAdvtOrigAddrType, + mvpnSpmsiAdvtOrigAddr } - ::= { mvpnSpmsiTable 1 } + ::= { mvpnSpmsiAdvtTable 1 } - MvpnSpmsiEntry ::= SEQUENCE { - mvpnSpmsiCmcastAddrType InetAddressType, - mvpnSpmsiCmcastGroupAddr InetAddress, - mvpnSpmsiCmcastGroupPrefixLen InetAddressPrefixLength, - mvpnSpmsiCmcastSourceAddr InetAddress, - mvpnSpmsiCmcastSourcePrefixLen InetAddressPrefixLength, - mvpnSpmsiOrigAddrType InetAddressType, - mvpnSpmsiOrigAddr InetAddress, - mvpnSpmsiTunnelAttribute RowPointer, - mvpnSpmsiUpTime TimeInterval, - mvpnSpmsiExpTime TimeInterval, - mvpnSpmsiRefCnt Unsigned32 + MvpnSpmsiAdvtEntry ::= SEQUENCE { + mvpnSpmsiAdvtCmcastAddrType InetAddressType, + mvpnSpmsiAdvtCmcastGroupAddr InetAddress, + mvpnSpmsiAdvtCmcastGroupPrefixLen InetAddressPrefixLength, + mvpnSpmsiAdvtCmcastSourceAddr InetAddress, + mvpnSpmsiAdvtCmcastSourcePrefixLen InetAddressPrefixLength, + mvpnSpmsiAdvtOrigAddrType InetAddressType, + mvpnSpmsiAdvtOrigAddr InetAddress, + mvpnSpmsiAdvtTunnelAttribute RowPointer, + mvpnSpmsiAdvtExpTime TimeInterval, + mvpnSpmsiAdvtRefCnt Unsigned32, + mvpnSpmsiAdvtReceived Counter32, + mvpnSpmsiAdvtReceivedError Counter32, + mvpnSpmsiAdvtMalformedTunnelType Counter32, + mvpnSpmsiAdvtMalformedTunnelId Counter32, + mvpnSpmsiAdvtLastReceivedTime TimeStamp, + mvpnSpmsiAdvtCounterDiscontinuityTime TimeStamp } - mvpnSpmsiCmcastAddrType OBJECT-TYPE + mvpnSpmsiAdvtCmcastAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION - "The Internet address type of mvpnSpmsiCmcastGroup/Source." - ::= { mvpnSpmsiEntry 1 } + "The Internet address type of mvpnSpmsiAdvtCmcastGroup/Source." + ::= { mvpnSpmsiAdvtEntry 1 } - mvpnSpmsiCmcastGroupAddr OBJECT-TYPE + mvpnSpmsiAdvtCmcastGroupAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "S-PMSI C-multicast group address. + If it is 0 (or ::0), this is a wildcard group, - and mvpnSpmsiCmcastGroupPrefixLen must be 32 (or 128). + and mvpnSpmsiAdvtCmcastGroupPrefixLen must be 32 (or 128). " - ::= { mvpnSpmsiEntry 2 } + ::= { mvpnSpmsiAdvtEntry 2 } - mvpnSpmsiCmcastGroupPrefixLen OBJECT-TYPE + mvpnSpmsiAdvtCmcastGroupPrefixLen OBJECT-TYPE SYNTAX InetAddressPrefixLength MAX-ACCESS not-accessible STATUS current DESCRIPTION "S-PMSI C-multicast group address prefix length." - ::= { mvpnSpmsiEntry 3 } + ::= { mvpnSpmsiAdvtEntry 3 } - mvpnSpmsiCmcastSourceAddr OBJECT-TYPE + mvpnSpmsiAdvtCmcastSourceAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "S-PMSI C-multicast source address If it is 0 (or ::0), this is a wildcard source, - and mvpnSpmsiCmcastSourcePrefixLen must be 32 (or 128). + and mvpnSpmsiAdvtCmcastSourcePrefixLen must be 32 (or 128). " - ::= { mvpnSpmsiEntry 4 } + ::= { mvpnSpmsiAdvtEntry 4 } - mvpnSpmsiCmcastSourcePrefixLen OBJECT-TYPE + mvpnSpmsiAdvtCmcastSourcePrefixLen OBJECT-TYPE SYNTAX InetAddressPrefixLength MAX-ACCESS not-accessible STATUS current DESCRIPTION "S-PMSI C-multicast source address prefix length." - ::= { mvpnSpmsiEntry 5 } + ::= { mvpnSpmsiAdvtEntry 5 } - mvpnSpmsiOrigAddrType OBJECT-TYPE + mvpnSpmsiAdvtOrigAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION - "The Internet address type of mvpnSpmsiOrigAddr." - ::= { mvpnSpmsiEntry 6 } + "The Internet address type of mvpnSpmsiAdvtOrigAddr." + ::= { mvpnSpmsiAdvtEntry 6 } - mvpnSpmsiOrigAddr OBJECT-TYPE + mvpnSpmsiAdvtOrigAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The BGP address of the PE that originated the S-PMSI." - ::= { mvpnSpmsiEntry 7 } + ::= { mvpnSpmsiAdvtEntry 7 } - mvpnSpmsiTunnelAttribute OBJECT-TYPE + mvpnSpmsiAdvtTunnelAttribute OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-only STATUS current DESCRIPTION "A row pointer to the l2L3VpnMcastPmsiTunnelAttributeTable" - ::= { mvpnSpmsiEntry 8 } - - mvpnSpmsiUpTime OBJECT-TYPE - SYNTAX TimeInterval - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The time since this S-PMSI - was first advertised/received by the PE. - " - ::= { mvpnSpmsiEntry 9 } + ::= { mvpnSpmsiAdvtEntry 8 } - mvpnSpmsiExpTime OBJECT-TYPE + mvpnSpmsiAdvtExpTime OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-only STATUS current DESCRIPTION "For UDP-based S-PMSI signaling for PIM-MVPN, the amount of time remaining before this received S-PMSI Join Message expires, or the next S-PMSI Join Message refresh is to be advertised again from the PE. Otherwise, it is 0. " - ::= { mvpnSpmsiEntry 10 } + ::= { mvpnSpmsiAdvtEntry 9 } - mvpnSpmsiRefCnt OBJECT-TYPE + mvpnSpmsiAdvtRefCnt OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of c-multicast routes that are mapped to this S-PMSI. " - ::= { mvpnSpmsiEntry 11 } + ::= { mvpnSpmsiAdvtEntry 10 } + + mvpnSpmsiAdvtReceived OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of S-PMSI advertisements received by the PE router. + This includes advertisements that were discarded. + Discontinuities in the value of this counter can + occur at re-initialization of the management system, + and at other times as indicated by the value of + mvpnIpmsiAdvtCounterDiscontinuityTime. + " + ::= { mvpnSpmsiAdvtEntry 11 } + + mvpnSpmsiAdvtReceivedError OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The total number of errors in the S-PMSI advertisements + received by the PE router. + The value of this object is the sum of + the values of mvpnSpmsiAdvtMalformedTunnelType and + mvpnSpmsiAdvtMalformedTunnelId. + Discontinuities in the value of this counter can + occur at re-initialization of the management system, + and at other times as indicated by the value of + mvpnSpmsiAdvtCounterDiscontinuityTime. + " + ::= { mvpnSpmsiAdvtEntry 12 } + + mvpnSpmsiAdvtMalformedTunnelType OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of received S-PMSI advertisements that + contain a PMSI Tunnel attribute whose Tunnel + Type field has an undefined tunnel type. + Discontinuities in the value of this counter can + occur at re-initialization of the management system, + and at other times as indicated by the value of + mvpnSpmsiAdvtCounterDiscontinuityTime. + " + REFERENCE + "RFC6514 Sec.5" + ::= { mvpnSpmsiAdvtEntry 13 } + + mvpnSpmsiAdvtMalformedTunnelId OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of received S-PMSI advertisements that + contain a PMSI Tunnel attribute whose Tunnel + Identifier field cannot be parsed as a + tunnel identifier of the tunnel types specified in + the Tunnel type field of the attribute. + Discontinuities in the value of this counter can + occur at re-initialization of the management system, + and at other times as indicated by the value of + mvpnSpmsiAdvtCounterDiscontinuityTime. + " + REFERENCE + "RFC6514 Sec.5" + ::= { mvpnSpmsiAdvtEntry 14 } + + mvpnSpmsiAdvtLastReceivedTime OBJECT-TYPE + SYNTAX TimeStamp + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value of sysUpTime when the last S-PMSI + advertisement was received by the PE router. + " + ::= { mvpnSpmsiAdvtEntry 15 } + + mvpnSpmsiAdvtCounterDiscontinuityTime OBJECT-TYPE + SYNTAX TimeStamp + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value of sysUpTime on the most recent occasion + at which any one or more of this syslog application's + counters, viz., counters with OID prefix + 'mvpnSpmsiAdvtReceived' or + 'mvpnSpmsiAdvtReceivedError' or + 'mvpnSpmsiAdvtMalformedTunnelType' or + 'mvpnSpmsiAdvtMalformedTunnelId' suffered a + discontinuity. + If no such discontinuities have occurred since the + last re-initialization of the local management + subsystem, then this object will have a zero value. + " + ::= { mvpnSpmsiAdvtEntry 16 } -- Table of multicast routes in an MVPN mvpnMrouteTable OBJECT-TYPE SYNTAX SEQUENCE OF MvpnMrouteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION - "This table augments ipMcastRouteTable, to provide some MVPN - specific information. + "This table contains multicast routing information + in MVRFs present in the PE. " ::= { mvpnStates 4 } mvpnMrouteEntry OBJECT-TYPE SYNTAX MvpnMrouteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION - "The mvpnMrouteEntry matches and augments an ipMcastRouteEntry, - with MVPN specific information, such as PMSI used. + "This entry corresponds to each of multicast routing + information components for IP datagrams + from a particular source and addressed to a particular + IP multicast group address. + + OIDs are limited to 128 sub-identifiers, but this limit + is not enforced by the syntax of this entry. In practice, + this does not present a problem, because IP address types + allowed by conformance statements do not exceed this limit. " - AUGMENTS { ipMcastRouteEntry } + INDEX { + mplsL3VpnVrfName, + mvpnMrouteCmcastGroupAddrType, + mvpnMrouteCmcastGroupAddr, + mvpnMrouteCmcastGroupPrefixLength, + mvpnMrouteCmcastSourceAddrType, + mvpnMrouteCmcastSourceAddr, + mvpnMrouteCmcastSourcePrefixLength + } ::= { mvpnMrouteTable 1 } MvpnMrouteEntry ::= SEQUENCE { + mvpnMrouteCmcastGroupAddrType InetAddressType, + mvpnMrouteCmcastGroupAddr InetAddress, + mvpnMrouteCmcastGroupPrefixLength InetAddressPrefixLength, + mvpnMrouteCmcastSourceAddrType InetAddressType, + mvpnMrouteCmcastSourceAddr InetAddress, + mvpnMrouteCmcastSourcePrefixLength InetAddressPrefixLength, + mvpnMrouteUpstreamNeighborAddrType InetAddressType, + mvpnMrouteUpstreamNeighborAddr InetAddress, + mvpnMrouteInIfIndex InterfaceIndexOrZero, + mvpnMrouteTimeStamp TimeStamp, + mvpnMrouteExpiryTime TimeTicks, + mvpnMrouteProtocol IANAipMRouteProtocol, + mvpnMrouteRtProtocol IANAipRouteProtocol, + mvpnMrouteRtAddrType InetAddressType, + mvpnMrouteRtAddr InetAddress, + mvpnMrouteRtPrefixLength InetAddressPrefixLength, + mvpnMrouteRtType INTEGER, + mvpnMrouteOctets Counter64, + mvpnMroutePkts Counter64, + mvpnMrouteTtlDropOctets Counter64, + mvpnMrouteTtlDropPackets Counter64, + mvpnMrouteDifferentInIfOctets Counter64, + mvpnMrouteDifferentInIfPackets Counter64, + mvpnMrouteBps CounterBasedGauge64, mvpnMroutePmsiPointer RowPointer, mvpnMrouteNumberOfLocalReplication Unsigned32, mvpnMrouteNumberOfRemoteReplication Unsigned32 } + mvpnMrouteCmcastGroupAddrType OBJECT-TYPE + SYNTAX InetAddressType + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A value indicating the address family of the address + contained in mvpnMrouteGroupAddr. Legal values correspond to + the subset of address families for which multicast + forwarding is supported." + ::= { mvpnMrouteEntry 1 } + + mvpnMrouteCmcastGroupAddr OBJECT-TYPE + SYNTAX InetAddress + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The IP multicast group address which, when combined with + the corresponding value specified in + mvpnMrouteGroupPrefixLength, identifies the groups for + which this entry contains multicast routing information. + + This address object is only significant up to + mvpnMrouteGroupPrefixLength bits. The remaining address + bits are set to zero. This is especially important for this + index field, which is part of the index of this entry. Any + non-zero bits would signify an entirely different entry. + + For addresses of type ipv4z or ipv6z, the appended zone + index is significant even though it lies beyond the prefix + length. The use of these address types indicate that this + forwarding state applies only within the given zone. Zone + index zero is not valid in this table." + ::= { mvpnMrouteEntry 2 } + + mvpnMrouteCmcastGroupPrefixLength OBJECT-TYPE + SYNTAX InetAddressPrefixLength + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The length in bits of the mask which, when combined with + the corresponding value of mvpnMrouteGroupAddr, identifies the + groups for which this entry contains multicast routing + information. + + The InetAddressType is given by + mvpnMrouteGroupAddrType. For values 'ipv4' and + 'ipv4z', this object must be in the range 4..32. For values + 'ipv6' and 'ipv6z', this object must be in the range + 8..128. + " + ::= { mvpnMrouteEntry 3 } + + mvpnMrouteCmcastSourceAddrType OBJECT-TYPE + SYNTAX InetAddressType + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A value indicating the address family of the address + contained in mvpnMrouteSourceAddr. + + A value of unknown(0) indicates a non-source-specific entry, + corresponding to all sources in the group. Otherwise, the + value MUST be the same as the value of + mvpnMrouteGroupAddrType. + " + ::= { mvpnMrouteEntry 4 } + + mvpnMrouteCmcastSourceAddr OBJECT-TYPE + SYNTAX InetAddress + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The network address which, when combined with the + corresponding value of mvpnMrouteSourcePrefixLength, + identifies the sources for which this entry contains + multicast routing information. + + This address object is only significant up to + mvpnMrouteSourcePrefixLength bits. The remaining address + bits are set to zero. This is especially important for this + index field, which is part of the index of this entry. Any + non-zero bits would signify an entirely different entry. + + For addresses of type ipv4z or ipv6z, the appended zone + index is significant even though it lies beyond the prefix + length. The use of these address types indicate that this + source address applies only within the given zone. Zone + index zero is not valid in this table. + " + ::= { mvpnMrouteEntry 5 } + + mvpnMrouteCmcastSourcePrefixLength OBJECT-TYPE + SYNTAX InetAddressPrefixLength + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The length in bits of the mask which, when combined with + the corresponding value of mvpnMrouteSource, identifies + the sources for which this entry contains multicast routing + information. + + The InetAddressType is given by + mvpnMrouteSourceAddrType. For the value 'unknown', + this object must be zero. For values 'ipv4' and 'ipv4z', + this object must be in the range 4..32. For values 'ipv6' + and 'ipv6z', this object must be in the range 8..128." + ::= { mvpnMrouteEntry 6 } + + mvpnMrouteUpstreamNeighborAddrType OBJECT-TYPE + SYNTAX InetAddressType + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "A value indicating the address family of the address + contained in mvpnMrouteUpstreamNeighborAddr. + + An address type of unknown(0) indicates that the upstream + neighbor is unknown, for example in BIDIR-PIM." + REFERENCE "RFC 5015" + ::= { mvpnMrouteEntry 7 } + + mvpnMrouteUpstreamNeighborAddr OBJECT-TYPE + SYNTAX InetAddress + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The address of the upstream neighbor (for example, RPF + neighbor) from which IP datagrams from these sources to + this multicast address are received. + " + ::= { mvpnMrouteEntry 8 } + + mvpnMrouteInIfIndex OBJECT-TYPE + SYNTAX InterfaceIndexOrZero + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value of ifIndex for the interface on which IP + datagrams sent by these sources to this multicast address + are received. A value of 0 indicates that datagrams are not + subject to an incoming interface check, but may be accepted + on multiple interfaces (for example, in BIDIR-PIM). + " + REFERENCE + "RFC 5015" + ::= { mvpnMrouteEntry 9 } + + mvpnMrouteTimeStamp OBJECT-TYPE + SYNTAX TimeStamp + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value of sysUpTime at which the multicast routing + information represented by this entry was learned by the + router. + + If this information was present at the most recent re- + initialization of the local management subsystem, then this + object contains a zero value. + " + ::= { mvpnMrouteEntry 10 } + + mvpnMrouteExpiryTime OBJECT-TYPE + SYNTAX TimeTicks + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The minimum amount of time remaining before this entry will + be aged out. The value 0 indicates that the entry is not + subject to aging. If mvpnMrouteNextHopState is pruned(1), + this object represents the remaining time until the prune + expires. If this timer expires, state reverts to + forwarding(2). Otherwise, this object represents the time + until this entry is removed from the table. + " + ::= { mvpnMrouteEntry 11 } + + mvpnMrouteProtocol OBJECT-TYPE + SYNTAX IANAipMRouteProtocol + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The multicast routing protocol via which this multicast + forwarding entry was learned. + " + ::= { mvpnMrouteEntry 12 } + + mvpnMrouteRtProtocol OBJECT-TYPE + SYNTAX IANAipRouteProtocol + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The routing mechanism via which the route used to find the + upstream or parent interface for this multicast forwarding + entry was learned. + " + ::= { mvpnMrouteEntry 13 } + + mvpnMrouteRtAddrType OBJECT-TYPE + SYNTAX InetAddressType + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "A value indicating the address family of the address + contained in mvpnMrouteRtAddr. + " + ::= { mvpnMrouteEntry 14 } + + mvpnMrouteRtAddr OBJECT-TYPE + SYNTAX InetAddress + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The address portion of the route used to find the upstream + or parent interface for this multicast forwarding entry. + + This address object is only significant up to + mvpnMrouteRtPrefixLength bits. The remaining address bits + are set to zero. + + For addresses of type ipv4z or ipv6z, the appended zone + index is significant even though it lies beyond the prefix + length. The use of these address types indicate that this + forwarding state applies only within the given zone. Zone + index zero is not valid in this table. + " + ::= { mvpnMrouteEntry 15 } + + mvpnMrouteRtPrefixLength OBJECT-TYPE + SYNTAX InetAddressPrefixLength + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The length in bits of the mask associated with the route + used to find the upstream or parent interface for this + multicast forwarding entry. + + The InetAddressType is given by mvpnMrouteRtAddressType. + For values 'ipv4' and 'ipv4z', this object must be in the + range 4..32. For values 'ipv6' and 'ipv6z', this object + must be in the range 8..128. + " + ::= { mvpnMrouteEntry 16 } + + mvpnMrouteRtType OBJECT-TYPE + SYNTAX INTEGER { + unicast (1), -- Unicast route used in multicast RIB + multicast (2) -- Multicast route + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The reason the given route was placed in the (logical) + multicast Routing Information Base (RIB). A value of + unicast means that the route would normally be placed only + in the unicast RIB, but was placed in the multicast RIB + due (instead or in addition) to local configuration, such as + when running PIM over RIP. A value of multicast means that + the route was explicitly added to the multicast RIB by the + routing protocol, such as the Distance Vector Multicast + Routing Protocol (DVMRP) or Multiprotocol BGP. + " + ::= { mvpnMrouteEntry 17 } + + mvpnMrouteOctets OBJECT-TYPE + SYNTAX Counter64 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of octets contained in IP datagrams that were + received from these sources and addressed to this multicast + group address, and which were forwarded by this router. + + Discontinuities in this monotonically increasing value + occur at re-initialization of the management system. + Discontinuities can also occur as a result of routes being + removed and replaced, which can be detected by observing + the value of mvpnMrouteTimeStamp. + " + ::= { mvpnMrouteEntry 18 } + + mvpnMroutePkts OBJECT-TYPE + SYNTAX Counter64 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of packets routed using this multicast route + entry. + + Discontinuities in this monotonically increasing value + occur at re-initialization of the management system. + Discontinuities can also occur as a result of routes being + removed and replaced, which can be detected by observing + the value of mvpnMrouteTimeStamp. + " + ::= { mvpnMrouteEntry 19 } + + mvpnMrouteTtlDropOctets OBJECT-TYPE + SYNTAX Counter64 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of octets contained in IP datagrams that this + router has received from these sources and addressed to this + multicast group address, which were dropped because the TTL + (IPv4) or Hop Limit (IPv6) was decremented to zero, or to a + value less than ipMcastInterfaceTtl for all next hops. + + Discontinuities in this monotonically increasing value + occur at re-initialization of the management system. + Discontinuities can also occur as a result of routes being + removed and replaced, which can be detected by observing + the value of mvpnMrouteTimeStamp. + " + ::= { mvpnMrouteEntry 20 } + + mvpnMrouteTtlDropPackets OBJECT-TYPE + SYNTAX Counter64 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of packets that this router has received from + these sources and addressed to this multicast group address, + which were dropped because the TTL (IPv4) or Hop Limit + (IPv6) was decremented to zero, or to a value less than + ipMcastInterfaceTtl for all next hops. + + Discontinuities in this monotonically increasing value + occur at re-initialization of the management system. + Discontinuities can also occur as a result of routes being + removed and replaced, which can be detected by observing + the value of mvpnMrouteTimeStamp. + " + ::= { mvpnMrouteEntry 21 } + + mvpnMrouteDifferentInIfOctets OBJECT-TYPE + SYNTAX Counter64 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of octets contained in IP datagrams that this + router has received from these sources and addressed to this + multicast group address, which were dropped because they + were received on an unexpected interface. + + For RPF checking protocols (such as PIM-SM), these packets + arrived on interfaces other than mvpnMrouteInIfIndex, and + were dropped because of this failed RPF check. (RPF paths + are 'Reverse Path Forwarding' paths; the unicast routes to + the expected origin of multicast data flows). + Other protocols may drop packets on an incoming interface + check for different reasons (for example, BIDIR-PIM performs + a DF check on receipt of packets). All packets dropped as a + result of an incoming interface check are counted here. + + If this counter increases rapidly, this indicates a problem. + A significant quantity of multicast data is arriving at this + router on unexpected interfaces, and is not being forwarded. + + For guidance, if the rate of increase of this counter + exceeds 1% of the rate of increase of mvpnMrouteOctets, + then there are multicast routing problems that require + investigation. + + Discontinuities in this monotonically increasing value + occur at re-initialization of the management system. + Discontinuities can also occur as a result of routes being + removed and replaced, which can be detected by observing + the value of mvpnMrouteTimeStamp. + " + REFERENCE + "RFC 4601 + RFC 5015 + " + ::= { mvpnMrouteEntry 22 } + + mvpnMrouteDifferentInIfPackets OBJECT-TYPE + SYNTAX Counter64 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of packets which this router has received from + these sources and addressed to this multicast group address, + which were dropped because they were received on an + unexpected interface. + + For RPF checking protocols (such as PIM-SM), these packets + arrived on interfaces other than mvpnMrouteInIfIndex, and + were dropped because of this failed RPF check. (RPF paths + are 'Reverse Path Forwarding' path; the unicast routes to + the expected origin of multicast data flows). + + Other protocols may drop packets on an incoming interface + check for different reasons (for example, BIDIR-PIM performs + a DF check on receipt of packets). All packets dropped as a + result of an incoming interface check are counted here. + + If this counter increases rapidly, this indicates a problem. + A significant quantity of multicast data is arriving at this + router on unexpected interfaces, and is not being forwarded. + + For guidance, if the rate of increase of this counter + exceeds 1% of the rate of increase of mvpnMroutePkts, then + there are multicast routing problems that require + investigation. + + Discontinuities in this monotonically increasing value + occur at re-initialization of the management system. + Discontinuities can also occur as a result of routes being + removed and replaced, which can be detected by observing + the value of mvpnMrouteTimeStamp. + " + REFERENCE + "RFC 4601 + RFC 5015 + " + ::= { mvpnMrouteEntry 23 } + + mvpnMrouteBps OBJECT-TYPE + SYNTAX CounterBasedGauge64 + UNITS "bits per second" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Bits per second forwarded by this router using this + multicast routing entry. + + This value is a sample; it is the number of bits forwarded + during the last whole 1 second sampling period. The value + during the current 1 second sampling period is not made + available until the period is completed. + + The quantity being sampled is the same as that measured by + mvpnMrouteOctets. The units and the sampling method are + different. + " + ::= { mvpnMrouteEntry 24 } + mvpnMroutePmsiPointer OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-only STATUS current DESCRIPTION "The I-PMSI or S-PMSI this C-multicast route is using. This is important because an implementation may not have an interface corresponding to a provider tunnel, - that can be used in ipMcastRouteNextHopEntry. + that can be used in mvpnMrouteNextHopEntry. " - ::= { mvpnMrouteEntry 1 } + ::= { mvpnMrouteEntry 25 } mvpnMrouteNumberOfLocalReplication OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of replications for local receivers. For example, if an ingress PE needs to send traffic out of N PE-CE interfaces, then mvpnMrouteNumberOfLocalReplication is N. " - ::= { mvpnMrouteEntry 2 } + ::= { mvpnMrouteEntry 26 } mvpnMrouteNumberOfRemoteReplication OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of local replications for remote PEs. For example, if the number of remote PEs that need to receive traffic is N, then mvpnMrouteNumberOfRemoteReplication is N in case of Ingress Replication, but may be less than N in case of RSVP-TE or mLDP P2MP tunnels, depending on the actual number of replications the PE needs do. " - ::= { mvpnMrouteEntry 3 } + + ::= { mvpnMrouteEntry 27 } + + mvpnMrouteNextHopTable OBJECT-TYPE + SYNTAX SEQUENCE OF MvpnMrouteNextHopEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The (conceptual) table containing information on the + next-hops on outgoing interfaces for routing IP multicast + datagrams. Each entry is one of a list of next-hops on + outgoing interfaces for particular sources sending to a + particular multicast group address." + ::= { mvpnStates 5 } + + mvpnMrouteNextHopEntry OBJECT-TYPE + SYNTAX MvpnMrouteNextHopEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "An entry (conceptual row) in the list of next-hops on + outgoing interfaces to which IP multicast datagrams from + particular sources to an IP multicast group address are + routed. + + OIDs are limited to 128 sub-identifiers, but this limit + is not enforced by the syntax of this entry. In practice, + this does not present a problem, because IP address types + allowed by conformance statements do not exceed this limit. + " + INDEX { + mplsL3VpnVrfName, + mvpnMrouteNextHopGroupAddrType, + mvpnMrouteNextHopGroupAddr, + mvpnMrouteNextHopGroupPrefixLength, + mvpnMrouteNextHopSourceAddrType, + mvpnMrouteNextHopSourceAddr, + mvpnMrouteNextHopSourcePrefixLength, + mvpnMrouteNextHopIfIndex, + mvpnMrouteNextHopAddrType, + mvpnMrouteNextHopAddr + } + ::= { mvpnMrouteNextHopTable 1 } + + MvpnMrouteNextHopEntry ::= SEQUENCE { + mvpnMrouteNextHopGroupAddrType InetAddressType, + mvpnMrouteNextHopGroupAddr InetAddress, + mvpnMrouteNextHopGroupPrefixLength InetAddressPrefixLength, + mvpnMrouteNextHopSourceAddrType InetAddressType, + mvpnMrouteNextHopSourceAddr InetAddress, + mvpnMrouteNextHopSourcePrefixLength InetAddressPrefixLength, + mvpnMrouteNextHopIfIndex InterfaceIndex, + mvpnMrouteNextHopAddrType InetAddressType, + mvpnMrouteNextHopAddr InetAddress, + mvpnMrouteNextHopState INTEGER, + mvpnMrouteNextHopTimeStamp TimeStamp, + mvpnMrouteNextHopExpiryTime TimeTicks, + mvpnMrouteNextHopClosestMemberHops Unsigned32, + mvpnMrouteNextHopProtocol IANAipMRouteProtocol, + mvpnMrouteNextHopOctets Counter64, + mvpnMrouteNextHopPkts Counter64 + } + + mvpnMrouteNextHopGroupAddrType OBJECT-TYPE + SYNTAX InetAddressType + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A value indicating the address family of the address + contained in mvpnMrouteNextHopGroupAddr. Legal values + correspond to the subset of address families for which + multicast forwarding is supported. + " + ::= { mvpnMrouteNextHopEntry 1 } + + mvpnMrouteNextHopGroupAddr OBJECT-TYPE + SYNTAX InetAddress + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The IP multicast group address which, when combined with + the corresponding value specified in + mvpnMrouteNextHopGroupPrefixLength, identifies the groups + for which this entry contains multicast forwarding + information. + + This address object is only significant up to + mvpnMrouteNextHopGroupPrefixLength bits. The remaining + address bits are set to zero. This is especially important + for this index field, which is part of the index of this + entry. Any non-zero bits would signify an entirely + different entry. + + For addresses of type ipv4z or ipv6z, the appended zone + index is significant even though it lies beyond the prefix + length. The use of these address types indicate that this + forwarding state applies only within the given zone. Zone + index zero is not valid in this table. + " + ::= { mvpnMrouteNextHopEntry 2 } + + mvpnMrouteNextHopGroupPrefixLength OBJECT-TYPE + SYNTAX InetAddressPrefixLength + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The length in bits of the mask which, when combined with + the corresponding value of mvpnMrouteGroup, identifies the + groups for which this entry contains multicast routing + information. + + The InetAddressType is given by + mvpnMrouteNextHopGroupAddressType. For values 'ipv4' and + 'ipv4z', this object must be in the range 4..32. For values + 'ipv6' and 'ipv6z', this object must be in the range + 8..128. + " + ::= { mvpnMrouteNextHopEntry 3 } + + mvpnMrouteNextHopSourceAddrType OBJECT-TYPE + SYNTAX InetAddressType + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A value indicating the address family of the address + contained in mvpnMrouteNextHopSourceAddr. + + A value of unknown(0) indicates a non-source-specific entry, + corresponding to all sources in the group. Otherwise, the + value MUST be the same as the value of + mvpnMrouteNextHopGroupAddrType." + ::= { mvpnMrouteNextHopEntry 4 } + + mvpnMrouteNextHopSourceAddr OBJECT-TYPE + SYNTAX InetAddress + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The network address which, when combined with the + corresponding value of the mask specified in + mvpnMrouteNextHopSourcePrefixLength, identifies the + sources for which this entry specifies a next-hop on an + outgoing interface. + + This address object is only significant up to + mvpnMrouteNextHopSourcePrefixLength bits. The remaining + address bits are set to zero. This is especially important + for this index field, which is part of the index of this + entry. Any non-zero bits would signify an entirely + different entry. + + For addresses of type ipv4z or ipv6z, the appended zone + index is significant even though it lies beyond the prefix + length. The use of these address types indicate that this + source address applies only within the given zone. Zone + index zero is not valid in this table. + " + ::= { mvpnMrouteNextHopEntry 5 } + + mvpnMrouteNextHopSourcePrefixLength OBJECT-TYPE + SYNTAX InetAddressPrefixLength + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The length in bits of the mask which, when combined with + the corresponding value specified in + mvpnMrouteNextHopSource, identifies the sources for which + this entry specifies a next-hop on an outgoing interface. + The InetAddressType is given by + mvpnMrouteNextHopSourceAddressType. For the value + 'unknown', this object must be zero. For values 'ipv4' and + 'ipv4z', this object must be in the range 4..32. For values + 'ipv6' and 'ipv6z', this object must be in the range + 8..128. + " + ::= { mvpnMrouteNextHopEntry 6 } + + mvpnMrouteNextHopIfIndex OBJECT-TYPE + SYNTAX InterfaceIndex + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The ifIndex value of the interface for the outgoing + interface for this next-hop. + " + ::= { mvpnMrouteNextHopEntry 7 } + + mvpnMrouteNextHopAddrType OBJECT-TYPE + SYNTAX InetAddressType + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A value indicating the address family of the address + contained in mvpnMrouteNextHopAddr. + " + ::= { mvpnMrouteNextHopEntry 8 } + + mvpnMrouteNextHopAddr OBJECT-TYPE + SYNTAX InetAddress + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The address of the next-hop specific to this entry. For + most interfaces, this is identical to + mvpnMrouteNextHopGroup. Non-Broadcast Multi-Access + (NBMA) interfaces, however, may + have multiple next-hop addresses out a single outgoing + interface. + " + ::= { mvpnMrouteNextHopEntry 9 } + + mvpnMrouteNextHopState OBJECT-TYPE + SYNTAX INTEGER { pruned(1), forwarding(2) } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "An indication of whether the outgoing interface and next- + hop represented by this entry is currently being used to + forward IP datagrams. The value 'forwarding' indicates it + is currently being used; the value 'pruned' indicates it is + not. + " + ::= { mvpnMrouteNextHopEntry 10 } + + mvpnMrouteNextHopTimeStamp OBJECT-TYPE + SYNTAX TimeStamp + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value of sysUpTime at which the multicast routing + information represented by this entry was learned by the + router. + + If this information was present at the most recent re- + initialization of the local management subsystem, then this + object contains a zero value. + " + ::= { mvpnMrouteNextHopEntry 11 } + + mvpnMrouteNextHopExpiryTime OBJECT-TYPE + SYNTAX TimeTicks + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The minimum amount of time remaining before this entry will + be aged out. If mvpnMrouteNextHopState is pruned(1), the + remaining time until the prune expires and the state reverts + to forwarding(2). Otherwise, the remaining time until this + entry is removed from the table. The time remaining may be + copied from mvpnMrouteExpiryTime if the protocol in use + for this entry does not specify next-hop timers. The value + 0 indicates that the entry is not subject to aging. + " + ::= { mvpnMrouteNextHopEntry 12 } + + mvpnMrouteNextHopClosestMemberHops OBJECT-TYPE + SYNTAX Unsigned32 (0..256) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The minimum number of hops between this router and any + member of this IP multicast group reached via this next-hop + on this outgoing interface. Any IP multicast datagrams for + the group that have a TTL (IPv4) or Hop Count (IPv6) less + than this number of hops will not be forwarded to this + next-hop. + + A value of 0 means all multicast datagrams are forwarded out + the interface. A value of 256 means that no multicast + datagrams are forwarded out the interface. + + This is an optimization applied by multicast routing + protocols that explicitly track hop counts to downstream + listeners. Multicast protocols that are not aware of hop + counts to downstream listeners set this object to 0. + " + ::= { mvpnMrouteNextHopEntry 13 } + + mvpnMrouteNextHopProtocol OBJECT-TYPE + SYNTAX IANAipMRouteProtocol + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The routing mechanism via which this next-hop was learned." + ::= { mvpnMrouteNextHopEntry 14 } + + mvpnMrouteNextHopOctets OBJECT-TYPE + SYNTAX Counter64 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of octets of multicast packets that have been + forwarded using this route. + + Discontinuities in this monotonically increasing value + occur at re-initialization of the management system. + Discontinuities can also occur as a result of routes being + removed and replaced, which can be detected by observing + the value of mvpnMrouteNextHopTimeStamp." + ::= { mvpnMrouteNextHopEntry 15 } + + mvpnMrouteNextHopPkts OBJECT-TYPE + SYNTAX Counter64 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of packets which have been forwarded using this + route. + + Discontinuities in this monotonically increasing value + occur at re-initialization of the management system. + Discontinuities can also occur as a result of routes being + removed and replaced, which can be detected by observing + the value of ipMcastRouteNextHopTimeStamp." + ::= { mvpnMrouteNextHopEntry 16 } -- MVPN Notifications - mvpnMvrfChange NOTIFICATION-TYPE + mvpnMvrfOperationChange NOTIFICATION-TYPE OBJECTS { - mvpnGenMvrfStatusChange + mvpnGenMvrfLastOperation } STATUS current DESCRIPTION - "A mvpnMvrfChange notification signifies a change about + "A mvpnMvrfOperationChange notification signifies a change about a MVRF in the PE. The change event can be creation of the MVRF, deletion of the MVRF or an update on the I-PMSI - or S-PMSI configuration of the MVRF. The change event - is indicated by mvpnGenMvrfStatusChange embedded in + or S-PMSI information of the MVRF. The change event + is indicated by mvpnGenMvrfLastOperation embedded in the notification. The user can then query - mvpnGeneralTable, and/or mvpnSpmsiConfigTable to + mvpnGenericTable, mvpnPmsiTable, and/or mvpnSpmsiTable to get the details of the change as necessary. Note: Since the creation of a MVRF is often followed by configuration of I-PMSI and/or S-PMSIs for the MVRF, more than one (three at most) notifications for a MVRF may be generated serially, and it is really not necessary to generate all three of them. An agent may choose to generate a notification for the last event only, that is for S-PMSI configuration. Similarly, deletion of I-PMSI and S-PMSI configuration on a MVRF happens before a MVRF is deleted and it is recommended that the agent send the notification for MVRF deletion event only. " ::= { mvpnNotifications 1 } + mvpnMvrfGroupJoined NOTIFICATION-TYPE + OBJECTS { + mvpnMrouteTimeStamp + } + STATUS current + DESCRIPTION + "A mvpnMvrfGroupJoined notification signifies that + this PE has joined to a new multicast group + serviced in a particular MVPN. + The change event is indicated by mvpnMrouteTimeStamp + embedded in the notification. + " + ::= { mvpnNotifications 2 } + + mvpnMvrfGroupLeft NOTIFICATION-TYPE + OBJECTS { + mvpnMrouteTimeStamp + } + STATUS current + DESCRIPTION + "A mvpnMvrfGroupJoined notification signifies that + this PE has left from a multicast group + serviced in a particular MVPN. + The change event is indicated by mvpnMrouteTimeStamp + embedded in the notification. + " + ::= { mvpnNotifications 3 } + -- MVPN MIB Conformance Information mvpnGroups OBJECT IDENTIFIER ::= { mvpnConformance 1 } mvpnCompliances OBJECT IDENTIFIER ::= { mvpnConformance 2 } -- Compliance Statements mvpnModuleFullCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "Compliance statement for agents that provide full support for the MCAST-VPN-MIB " MODULE -- this module MANDATORY-GROUPS { mvpnScalarGroup, - mvpnGeneralGroup, - mvpnPmsiConfigGroup, - mvpnSpmsiConfigGroup, + mvpnGenericGroup, + mvpnPmsiGroup, mvpnSpmsiGroup, + mvpnSpmsiAdvtGroup, mvpnMrouteGroup, + mvpnMrouteNextHopGroup, mvpnNotificationGroup } GROUP mvpnIpmsiGroup DESCRIPTION "This group is mandatory for systems that support BGP signaling for I-PMSI. " GROUP mvpnInterAsIpmsiGroup DESCRIPTION "This group is mandatory for systems that support Inter-AS Segmented I-PMSI. " - GROUP mvpnBgpGeneralGroup + GROUP mvpnBgpGenericGroup DESCRIPTION "This group is mandatory for systems that support BGP-MVPN. " GROUP mvpnOptionalGroup DESCRIPTION "This group is optional. " @@ -1446,280 +2677,318 @@ " ::= { mvpnCompliances 1 } mvpnModuleReadOnlyCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "Compliance requirement for implementations that only provide read-only support for MCAST-VPN-MIB. Such devices can then be monitored but cannot be configured using this MIB module. + " MODULE -- this module MANDATORY-GROUPS { mvpnScalarGroup, - mvpnGeneralGroup, - mvpnPmsiConfigGroup, - mvpnSpmsiConfigGroup, + mvpnGenericGroup, + mvpnPmsiGroup, mvpnSpmsiGroup, + mvpnSpmsiAdvtGroup, mvpnMrouteGroup, + mvpnMrouteNextHopGroup, mvpnNotificationGroup } GROUP mvpnIpmsiGroup DESCRIPTION "This group is mandatory for systems that support BGP signaling for I-PMSI. " GROUP mvpnInterAsIpmsiGroup DESCRIPTION "This group is mandatory for systems that support Inter-AS Segmented I-PMSI. " - GROUP mvpnBgpGeneralGroup + GROUP mvpnBgpGenericGroup DESCRIPTION "This group is mandatory for systems that support BGP-MVPN. " GROUP mvpnOptionalGroup DESCRIPTION "This group is optional. " - OBJECT mvpnNotificationEnable - MIN-ACCESS read-only - DESCRIPTION "Write access is not required." - OBJECT mvpnGenCmcastRouteProtocol MIN-ACCESS read-only DESCRIPTION "Write access is not required." - OBJECT mvpnGenIpmsiConfig + OBJECT mvpnGenIpmsiInfo MIN-ACCESS read-only DESCRIPTION "Write access is not required." - OBJECT mvpnGenInterAsPmsiConfig + OBJECT mvpnGenInterAsPmsiInfo MIN-ACCESS read-only DESCRIPTION "Write access is not required." - OBJECT mvpnGenUmhSelection MIN-ACCESS read-only DESCRIPTION "Write access is not required." - OBJECT mvpnGenSiteType - MIN-ACCESS read-only - DESCRIPTION "Write access is not required." - - OBJECT mvpnGenSptnlLimit - MIN-ACCESS read-only - DESCRIPTION "Write access is not required." - - OBJECT mvpnPmsiConfigEncapsType + OBJECT mvpnGenCustomerSiteType MIN-ACCESS read-only DESCRIPTION "Write access is not required." - OBJECT mvpnSpmsiConfigThreshold + OBJECT mvpnGenSPTunnelLimit MIN-ACCESS read-only DESCRIPTION "Write access is not required." - OBJECT mvpnSpmsiConfigPmsiPointer + OBJECT mvpnPmsiEncapsulationType MIN-ACCESS read-only DESCRIPTION "Write access is not required." - OBJECT mvpnGenRowStatus - SYNTAX RowStatus { active(1) } - MIN-ACCESS read-only - DESCRIPTION "Write access is not required." - OBJECT mvpnPmsiConfigRowStatus - SYNTAX RowStatus { active(1) } + OBJECT mvpnSpmsiThreshold MIN-ACCESS read-only DESCRIPTION "Write access is not required." - OBJECT mvpnSpmsiConfigRowStatus - SYNTAX RowStatus { active(1) } + OBJECT mvpnSpmsiPmsiPointer MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { mvpnCompliances 2 } -- units of conformance mvpnScalarGroup OBJECT-GROUP OBJECTS { mvpnMvrfs, mvpnV4Mvrfs, mvpnV6Mvrfs, mvpnPimV4Mvrfs, mvpnPimV6Mvrfs, mvpnBgpV4Mvrfs, mvpnBgpV6Mvrfs, - mvpnMldpMvrfs, - mvpnNotificationEnable + mvpnMldpMvrfs } STATUS current DESCRIPTION "These objects are used to monitor/manage global MVPN parameters. " ::= { mvpnGroups 1 } - mvpnGeneralGroup OBJECT-GROUP + mvpnGenericGroup OBJECT-GROUP OBJECTS { - mvpnGenMvrfStatusChange, - mvpnGenMvrfStatusChangeTime, + mvpnGenMvrfLastOperation, + mvpnGenMvrfLastOperationTime, mvpnGenCmcastRouteProtocol, - mvpnGenIpmsiConfig, - mvpnGenInterAsPmsiConfig, + mvpnGenIpmsiInfo, + mvpnGenInterAsPmsiInfo, mvpnGenUmhSelection, - mvpnGenSiteType, - mvpnGenSptnlLimit, - mvpnGenRowStatus + mvpnGenCustomerSiteType, + mvpnGenSPTunnelLimit } STATUS current DESCRIPTION "These objects are used to monitor/manage per-VRF MVPN parameters. " ::= { mvpnGroups 2 } - mvpnPmsiConfigGroup OBJECT-GROUP + mvpnPmsiGroup OBJECT-GROUP OBJECTS { - mvpnPmsiConfigEncapsType, - mvpnPmsiConfigRowStatus + mvpnPmsiEncapsulationType } STATUS current DESCRIPTION "These objects are used to monitor/manage PMSI tunnel configurations. " ::= { mvpnGroups 3 } - mvpnSpmsiConfigGroup OBJECT-GROUP + mvpnSpmsiGroup OBJECT-GROUP OBJECTS { - mvpnSpmsiConfigThreshold, - mvpnSpmsiConfigPmsiPointer, - mvpnSpmsiConfigRowStatus + mvpnSpmsiThreshold, + mvpnSpmsiPmsiPointer } STATUS current DESCRIPTION "These objects are used to monitor/manage S-PMSI configurations. " ::= { mvpnGroups 4 } mvpnIpmsiGroup OBJECT-GROUP OBJECTS { - mvpnIpmsiUpTime, - mvpnIpmsiAttribute + mvpnIpmsiAdvtTunnelAttribute, + mvpnIpmsiAdvtReceived, + mvpnIpmsiAdvtReceivedError, + mvpnIpmsiAdvtMalformedTunnelType, + mvpnIpmsiAdvtMalformedTunnelId, + mvpnIpmsiAdvtLastReceivedTime, + mvpnIpmsiAdvtCounterDiscontinuityTime + } STATUS current DESCRIPTION "These objects are used to monitor/manage Intra-AS I-PMSI attributes. " ::= { mvpnGroups 5 } mvpnInterAsIpmsiGroup OBJECT-GROUP OBJECTS { - mvpnInterAsIpmsiAttribute + mvpnInterAsIpmsiAdvtTunnelAttribute, + mvpnInterAsIpmsiAdvtReceived, + mvpnInterAsIpmsiAdvtReceivedError, + mvpnInterAsIpmsiAdvtMalformedTunnelType, + mvpnInterAsIpmsiAdvtMalformedTunnelId, + mvpnInterAsIpmsiAdvtLastReceivedTime, + mvpnInterAsIpmsiAdvtCounterDiscontinuityTime } STATUS current DESCRIPTION "These objects are used to monitor/manage Inter-AS I-PMSI attributes. " ::= { mvpnGroups 6 } - mvpnSpmsiGroup OBJECT-GROUP + mvpnSpmsiAdvtGroup OBJECT-GROUP OBJECTS { - mvpnSpmsiTunnelAttribute, - mvpnSpmsiUpTime, - mvpnSpmsiExpTime, - mvpnSpmsiRefCnt + mvpnSpmsiAdvtTunnelAttribute, + mvpnSpmsiAdvtExpTime, + mvpnSpmsiAdvtRefCnt, + mvpnSpmsiAdvtReceived, + mvpnSpmsiAdvtReceivedError, + mvpnSpmsiAdvtMalformedTunnelType, + mvpnSpmsiAdvtMalformedTunnelId, + mvpnSpmsiAdvtLastReceivedTime, + mvpnSpmsiAdvtCounterDiscontinuityTime } STATUS current DESCRIPTION "These objects are used to monitor/manage S-PMSI attributes. " ::= { mvpnGroups 7 } mvpnMrouteGroup OBJECT-GROUP OBJECTS { + mvpnMrouteUpstreamNeighborAddrType, + mvpnMrouteUpstreamNeighborAddr, + mvpnMrouteInIfIndex, + mvpnMrouteTimeStamp, + mvpnMrouteExpiryTime, + mvpnMrouteProtocol, + mvpnMrouteRtProtocol, + mvpnMrouteRtAddrType, + mvpnMrouteRtAddr, + mvpnMrouteRtPrefixLength, + mvpnMrouteRtType, + mvpnMrouteOctets, + mvpnMroutePkts, + mvpnMrouteTtlDropOctets, + mvpnMrouteTtlDropPackets, + mvpnMrouteDifferentInIfOctets, + mvpnMrouteDifferentInIfPackets, + mvpnMrouteBps, + mvpnMroutePmsiPointer, mvpnMrouteNumberOfLocalReplication, mvpnMrouteNumberOfRemoteReplication } STATUS current DESCRIPTION "These objects are used to monitor/manage VPN multicast forwarding states. " ::= { mvpnGroups 8 } - mvpnBgpGeneralGroup OBJECT-GROUP + mvpnMrouteNextHopGroup OBJECT-GROUP + OBJECTS { + mvpnMrouteNextHopState, + mvpnMrouteNextHopTimeStamp, + mvpnMrouteNextHopExpiryTime, + mvpnMrouteNextHopClosestMemberHops, + mvpnMrouteNextHopProtocol, + mvpnMrouteNextHopOctets, + mvpnMrouteNextHopPkts + } + STATUS current + DESCRIPTION + "These objects are used to monitor/manage + next hop information of VPN multicast. + " + ::= { mvpnGroups 9 } + + mvpnBgpGenericGroup OBJECT-GROUP OBJECTS { mvpnBgpGenMode, - mvpnBgpGenVrfRtImport, - mvpnBgpGenSrcAs + mvpnBgpGenVrfRouteImport, + mvpnBgpGenSrcAs, + mvpnBgpGenCmcastRouteWithdrawalTimer, + mvpnBgpGenSrcSharedTreeJoinTimer, + mvpnBgpGenMsgRateLimit, + mvpnBgpGenMaxSpmsiAdRoutes, + mvpnBgpGenMaxSpmsiAdRouteFreq, + mvpnBgpGenMaxSrcActiveAdRoutes, + mvpnBgpGenMaxSrcActiveAdRouteFreq } STATUS current DESCRIPTION "These objects are used to monitor/manage BGP-MVPN." - ::= { mvpnGroups 9 } + ::= { mvpnGroups 10 } mvpnOptionalGroup OBJECT-GROUP OBJECTS { mvpnMroutePmsiPointer } STATUS current DESCRIPTION "Support of these object is not required." - ::= { mvpnGroups 10 } + ::= { mvpnGroups 11 } mvpnNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { - mvpnMvrfChange + mvpnMvrfOperationChange, + mvpnMvrfGroupJoined, + mvpnMvrfGroupLeft } STATUS current DESCRIPTION "Objects required for MVPN notifications." - ::= { mvpnGroups 11 } + ::= { mvpnGroups 12 } END 4. Security Considerations This MIB contains some read-only objects that may be deemed senstive by some though perhaps not all operators. It also contains some read- write objects, whose setting will change the device's behavior related to MVPN. Appropriate security procedures related to SNMP in general but not specific to this MIB need to be implemented by concerned operators. There are a number of management objects defined in this MIB module with a MAX-ACCESS clause of read-write and/or read-create. Such objects may be considered sensitive or vulnerable in some network environments. The support for SET operations in a non-secure environment without proper protection opens devices to attack. These are the tables and objects and their sensitivity/vulnerability: - o mvpnNotificationEnable, mvpnGenCmcastRouteProtocol, - mvpnGenIpmsiConfig, mvpnGenInterAsPmsiConfig, mvpnGenUmhSelection, - mvpnGenSiteType, mvpnGenSptnlLimit, mvpnBgpGenMode, - mvpnBgpGenVrfRtImport, mvpnPmsiConfigEncapsType, - mvpnSpmsiConfigThreshold, mvpnSpmsiConfigPmsiPointer - - o mvpnGenRowStatus, mvpnPmsiConfigRowStatus, - mvpnSpmsiConfigRowStatus + o mvpnGenCmcastRouteProtocol, mvpnGenIpmsiInfo, + mvpnGenInterAsPmsiInfo, mvpnGenUmhSelection, + mvpnGenCustomerSiteType, mvpnGenSPTunnelLimit, mvpnBgpGenMode, + mvpnBgpGenVrfRtImport, mvpnPmsiEncapsulationType, + mvpnSpmsiThreshold, mvpnSpmsiPmsiPointer Some of the readable objects in this MIB module (i.e., objects with a MAX-ACCESS other than not-accessible) may be considered sensitive or vulnerable in some network environments. It is thus important to control even GET and/or NOTIFY access to these objects and possibly to even encrypt the values of these objects when sending them over the network via SNMP. These are the tables and objects and their sensitivity/vulnerability: o [TBD] @@ -1755,24 +3025,23 @@ This document borrowed some text from Cisco PIM-MVPN MIB [I-D.svaidya-mcast-vpn-mib]. We would like to thank Yakov Rekhter, Jeffrey Haas, Huajin Jeng, Durga Prasad Velamuri for their helpful comments. 7. References 7.1. Normative References - [I-D.ietf-bess-l2l3-vpn-mcast-mib] - Zhang, Z. and H. Tsunoda, "L2L3 VPN Multicast MIB", draft- - ietf-bess-l2l3-vpn-mcast-mib-12 (work in progress), - November 2017. + [RFC2003] Perkins, C., "IP Encapsulation within IP", RFC 2003, DOI + 10.17487/RFC2003, October 1996, . [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/ RFC2119, March 1997, . [RFC2578] McCloghrie, K., Ed., Perkins, D., Ed., and J. Schoenwaelder, Ed., "Structure of Management Information Version 2 (SMIv2)", STD 58, RFC 2578, DOI 10.17487/ RFC2578, April 1999, . [RFC2580] McCloghrie, K., Ed., Perkins, D., Ed., and J. Schoenwaelder, Ed., "Conformance Statements for SMIv2", STD 58, RFC 2580, DOI 10.17487/RFC2580, April 1999, . + [RFC2784] Farinacci, D., Li, T., Hanks, S., Meyer, D., and P. + Traina, "Generic Routing Encapsulation (GRE)", RFC 2784, + DOI 10.17487/RFC2784, March 2000, . + + [RFC2863] McCloghrie, K. and F. Kastenholz, "The Interfaces Group + MIB", RFC 2863, DOI 10.17487/RFC2863, June 2000, + . + + [RFC3032] Rosen, E., Tappan, D., Fedorkow, G., Rekhter, Y., + Farinacci, D., Li, T., and A. Conta, "MPLS Label Stack + Encoding", RFC 3032, DOI 10.17487/RFC3032, January 2001, + . + [RFC3414] Blumenthal, U. and B. Wijnen, "User-based Security Model (USM) for version 3 of the Simple Network Management Protocol (SNMPv3)", STD 62, RFC 3414, DOI 10.17487/ RFC3414, December 2002, . [RFC3826] Blumenthal, U., Maino, F., and K. McCloghrie, "The Advanced Encryption Standard (AES) Cipher Algorithm in the SNMP User-based Security Model", RFC 3826, DOI 10.17487/ RFC3826, June 2004, . [RFC4382] Nadeau, T., Ed. and H. van der Linde, Ed., "MPLS/BGP Layer 3 Virtual Private Network (VPN) Management Information Base", RFC 4382, DOI 10.17487/RFC4382, February 2006, . - [RFC5132] McWalter, D., Thaler, D., and A. Kessler, "IP Multicast - MIB", RFC 5132, DOI 10.17487/RFC5132, December 2007, - . + [RFC4659] De Clercq, J., Ooms, D., Carugi, M., and F. Le Faucheur, + "BGP-MPLS IP Virtual Private Network (VPN) Extension for + IPv6 VPN", RFC 4659, DOI 10.17487/RFC4659, September 2006, + . [RFC5591] Harrington, D. and W. Hardaker, "Transport Security Model for the Simple Network Management Protocol (SNMP)", STD 78, RFC 5591, DOI 10.17487/RFC5591, June 2009, . [RFC5592] Harrington, D., Salowey, J., and W. Hardaker, "Secure Shell Transport Model for the Simple Network Management Protocol (SNMP)", RFC 5592, DOI 10.17487/RFC5592, June 2009, . @@ -1837,20 +3121,23 @@ Qiu, "Wildcards in Multicast VPN Auto-Discovery Routes", RFC 6625, DOI 10.17487/RFC6625, May 2012, . [RFC7761] Fenner, B., Handley, M., Holbrook, H., Kouvelas, I., Parekh, R., Zhang, Z., and L. Zheng, "Protocol Independent Multicast - Sparse Mode (PIM-SM): Protocol Specification (Revised)", STD 83, RFC 7761, DOI 10.17487/RFC7761, March 2016, . + [RTPROTO] IANA, "IP Route Protocol MIB", 2016, + . + 7.2. Informative References [I-D.svaidya-mcast-vpn-mib] Vaidya, S., "Multicast in BGP/MPLS IP VPNs Management Information Base", draft-svaidya-mcast-vpn-mib-02 (work in progress), March 2005. [RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart, "Introduction and Applicability Statements for Internet- Standard Management Framework", RFC 3410, DOI 10.17487/