draft-ietf-bess-mvpn-mib-05.txt   draft-ietf-bess-mvpn-mib-06.txt 
Network Working Group Z. Zhang, Ed. Network Working Group Z. Zhang, Ed.
Internet-Draft Juniper Internet-Draft Juniper
Intended status: Standards Track S. Asif Intended status: Standards Track S. Asif
Expires: June 11, 2018 AT&T Expires: November 1, 2018 AT&T
A. Green A. Green
BT BT
S. Gulranjani S. Gulranjani
Cisco Cisco
P. Jain P. Jain
Alcatel-Lucent Alcatel-Lucent
H. Tsunoda, Ed. H. Tsunoda, Ed.
Tohoku Institute of Technology Tohoku Institute of Technology
December 08, 2017 April 30, 2018
BGP/MPLS Layer 3 VPN Multicast Management Information Base BGP/MPLS Layer 3 VPN Multicast Management Information Base
draft-ietf-bess-mvpn-mib-05 draft-ietf-bess-mvpn-mib-06
Abstract Abstract
This memo defines a portion of the Management Information Base (MIB) This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community. for use with network management protocols in the Internet community.
In particular, it describes managed objects to configure and/or In particular, it describes managed objects to configure and/or
monitor MVPN, Multicast in MultiProtocol Label Switching/Border monitor MVPN, Multicast in MultiProtocol Label Switching/Border
Gateway Protocol (MPLS/BGP) IP Virtual Private Networks (VPNs) on a Gateway Protocol (MPLS/BGP) IP Virtual Private Networks (VPNs) on a
Provider Edge router. Provider Edge router.
skipping to change at page 1, line 44 skipping to change at page 1, line 44
Internet-Drafts are working documents of the Internet Engineering Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet- working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/. Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress." material or to cite them other than as "work in progress."
This Internet-Draft will expire on June 11, 2018. This Internet-Draft will expire on November 1, 2018.
Copyright Notice Copyright Notice
Copyright (c) 2017 IETF Trust and the persons identified as the Copyright (c) 2018 IETF Trust and the persons identified as the
document authors. All rights reserved. document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of (http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License. described in the Simplified BSD License.
Table of Contents Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
1.1. Terminology . . . . . . . . . . . . . . . . . . . . . . . 3 1.1. Terminology . . . . . . . . . . . . . . . . . . . . . . . 3
2. The Internet-Standard Management Framework . . . . . . . . . 4 2. The Internet-Standard Management Framework . . . . . . . . . 4
3. MCAST-VPN-MIB . . . . . . . . . . . . . . . . . . . . . . . . 4 3. MCAST-VPN-MIB . . . . . . . . . . . . . . . . . . . . . . . . 4
3.1. Summary of MIB Module . . . . . . . . . . . . . . . . . . 4 3.1. Summary of MIB Module . . . . . . . . . . . . . . . . . . 4
3.2. MIB Module Definitions . . . . . . . . . . . . . . . . . 7 3.2. MIB Module Definitions . . . . . . . . . . . . . . . . . 6
4. Security Considerations . . . . . . . . . . . . . . . . . . . 36 4. Security Considerations . . . . . . . . . . . . . . . . . . . 62
5. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 37 5. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 63
6. Acknowledgement . . . . . . . . . . . . . . . . . . . . . . . 37 6. Acknowledgement . . . . . . . . . . . . . . . . . . . . . . . 64
7. References . . . . . . . . . . . . . . . . . . . . . . . . . 37 7. References . . . . . . . . . . . . . . . . . . . . . . . . . 64
7.1. Normative References . . . . . . . . . . . . . . . . . . 37 7.1. Normative References . . . . . . . . . . . . . . . . . . 64
7.2. Informative References . . . . . . . . . . . . . . . . . 39 7.2. Informative References . . . . . . . . . . . . . . . . . 66
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 39 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 66
1. Introduction 1. Introduction
[RFC6513], [RFC6514], and [RFC6625] specify procedures for supporting [RFC6513], [RFC6514], and [RFC6625] specify procedures for supporting
multicast in Border Gateway Protocol/MultiProtocol Label Switching multicast in Border Gateway Protocol/MultiProtocol Label Switching
(BGP/MPLS) Layer 3 (IP) Virtual Private Network (VPN). Throughout (BGP/MPLS) Layer 3 (IP) Virtual Private Network (VPN). Throughout
this document, we will use the term "Multicast VPN (MVPN)" [RFC6513] this document, we will use the term "Multicast VPN (MVPN)" [RFC6513]
to refer to a BGP/MPLS IP VPN that supports multicast. to refer to a BGP/MPLS IP VPN that supports multicast.
Provider Edge routers (PEs) exchange the VPN customer multicast Provider Edge routers (PEs) exchange the VPN customer multicast
skipping to change at page 3, line 38 skipping to change at page 3, line 38
send customer multicast traffic to all or some PEs in the same VPN. send customer multicast traffic to all or some PEs in the same VPN.
There are two kinds of PMSI: "Inclusive PMSI (I-PMSI)" and "Selective There are two kinds of PMSI: "Inclusive PMSI (I-PMSI)" and "Selective
PMSI (S-PMSI)" [RFC6513]. An I-PMSI is a PMSI that enables a PE PMSI (S-PMSI)" [RFC6513]. An I-PMSI is a PMSI that enables a PE
attached to a particular MVPN to transmit a message to all PEs in the attached to a particular MVPN to transmit a message to all PEs in the
same VPN. An S-PMSI is a PMSI that enables a PE attached to a same VPN. An S-PMSI is a PMSI that enables a PE attached to a
particular MVPN to transmit a message to some of the PEs in the same particular MVPN to transmit a message to some of the PEs in the same
VPN. VPN.
As described in [RFC4382], each PE router maintains one default As described in [RFC4382], each PE router maintains one default
forwarding table and "VPN Routing and Forwarding tables", or "VRFs". forwarding table and "Virtual Routing and Forwarding tables", or
Throughout this document, we will use the term "multicast VRF (MVRF)" "VRFs". Throughout this document, we will use the term "multicast
to refer a VRF that is configured to contain the multicast routing VRF (MVRF)" to refer a VRF that is configured to contain the
information. multicast routing information.
Interchangeably, the term MVRF and MVPN are used to refer to a Interchangeably, the term MVRF and MVPN are used to refer to a
particular Multicast VPN instantiation on a particular PE. particular Multicast VPN instantiation on a particular PE.
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119]. document are to be interpreted as described in [RFC2119].
2. The Internet-Standard Management Framework 2. The Internet-Standard Management Framework
skipping to change at page 4, line 27 skipping to change at page 4, line 27
RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580 RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
[RFC2580]. [RFC2580].
3. MCAST-VPN-MIB 3. MCAST-VPN-MIB
This document defines MCAST-VPN-MIB, a MIB module for monitoring and/ This document defines MCAST-VPN-MIB, a MIB module for monitoring and/
or configuring MVPNs on PEs. or configuring MVPNs on PEs.
3.1. Summary of MIB Module 3.1. Summary of MIB Module
The configuration and states specific to an MVPN include the MCAST-VPN-MIB provides the following functionalities for monitoring
following information elements: and configuring MVPN.
o C-multicast routing information exchange protocol (PIM or BGP)
o I-PMSI, S-PMSI and corresponding P-tunnels
o Mapping of C-multicast routing information to PMSI tunnels o Monitoring attribute informations of MVRFs of MVPNs presented on a
PE
To represent these information elements, MCAST-VPN-MIB defines eight o Configuring some timers related to a MVRF
tables: mvpnGeneralTable, mvpnBgpGeneralTable, mvpnSpmsiConfigTable,
mvpnPmsiConfigTable, mvpnIpmsiTable, mvpnInterAsIpmsiTable,
mvpnSpmsiTable, mvpnMrouteTable.
The following four tables represent the MVPN configurations on PEs. o Notifying creation, deletion, and modification of MVRFs on a PE
o mvpnGeneralTable o Monitoring attribute informations of PMSIs on a PE
o mvpnBgpGeneralTable o Monitoring advertisement exchanged by a PE
o mvpnSpmsiConfigTable o Monitoring routing entries in an MVRF
o mvpnPmsiConfigTable o Monitoring information on next-hops in an MVRF
The following diagram shows the relationship among those four tables o Notifying events that a PE joins or leaves a multicast group
use for configuration. Each box in the diagram represents a table,
and the label of each box corresponds to a table name. An arrow
indicates that one table has a pointer to a row in another table.
The entry in mvpnGeneralTable and mvpnSpmsiConfigTable has a pointer
to the row pertaining to the entry in the mvpnPmsiConfigTable.
+--------------+ To provide these functionalities, MCAST-VPN-MIB defines nine tables:
| mvpnBgp | mvpnGenericTable, mvpnBgpGenericlTable, mvpnPmsiTable,
| GeneralTable | mvpnSpmsiTable, mvpnIpmsiAdvtTable, mvpnInterAsIpmsiAdvtTable,
+--------------+ +-------------------+ +-----------------+ mvpnSpmsiAdvtTable, mvpnMrouteTable, and mvpnMrouteNextHopTable.
| mvpnGeneral | | mvpnPmsiConfig | | mvpnSpmsiConfig |
| Table | -> | Table | <- | Table |
+--------------+ +-------------------+ +-----------------+
o mvpnGeneralTable The following two tables contain information of MVRFs of MVPNs
configured on a PE.
This table represents MVPNs that are configured on a PE. Each o mvpnGenericTable
entry in this table is created for each MVRF representing an
instance of MVPN. The entry represetns general configuration/
states of the MVRF, including Inclusive PMSI (I-PMSI)
configuration. The MVPN represented by the entry in this table
must have the corresponding VRF in MPLS-L3VPN-STD-MIB [RFC4382].
o mvpnBgpGeneralTable This table specifies the generic information about MVRFs present
in a PE. Each entry in this table is created for each MVRF
representing an instance of MVPN. The entry represetns general
configuration/states of the MVRF, including Inclusive PMSI
(I-PMSI) configuration. An MVRF represented by the entry in this
table must have a corresponding VRF in MPLS-L3VPN-STD-MIB
[RFC4382].
This table augments the aformentioned mvpnGeneralTable. This o mvpnBgpGenericTable
table contains BGP-MVPN specific managed objects.
o mvpnSpmsiConfigTable This table specifies the specific information of MVRFs of MVPNs
that use BGP for exchanging C-Multicast routing information
present in a PE. Each MVRF of an MVPN that use BGP for exchanging
C-Multicast routing information will have an entry in this table.
The MVRF represented by this entry will have a corresponding entry
in the mvpnGenericTable.
This table contains managed objects necessary for configure The following two tables contain information of PMSIs configured on a
Selective PMSI (S-PMSI) associated with an MVRF on a PE. PE.
o mvpnPmsiConfigTable o mvpnPmsiTable
This table contains managed objects common to both I-PMSI and This table contains common managed objects representing attribute
S-PMSI configurations. Both I-PMSI configuration (in the entry in information of both I-PMSI and Selective PMSI (S-PMSI) configured
mvpnGeneralTable) and S-PMSI configuration (in the entry in on a PE. Both I-PMSI information (in the entry in
mvpnGeneralTable) and S-PMSI information (in the entry in
mvpnSpmsiConfigTable) refer to an entry in this table. mvpnSpmsiConfigTable) refer to an entry in this table.
The following four tables are designed for monitoring MVPNs on PEs.
o mvpnIpmsiTable
o mvpnInterAsIpmsiTable
o mvpnSpmsiTable o mvpnSpmsiTable
o mvpnMrouteTable This table contains managed objects representing attribute
The following diagram shows the relationship among these four tables information that is specific for S-PMSI associated with an MVRF on
and the l2l3VpnMcastPmsiTunnelAttributeTable defined separately in a PE.
L2L3-VPN-MCAST-MIB [I-D.ietf-bess-l2l3-vpn-mcast-mib]. The entry in
every table has a pointer to the row pertaining to the entry in the
l2l3VpnMcastPmsiTunnelAttributeTable.
+--------------+ +-------------------+ +-----------------+ The following three tables are designed for monitoring advertisements
| mvpnIpmsi | -> | l2L3VpnMcastPmsi | <- | mvpnSpmsi | that is advertised/received by a PE.
| Table | | TunnelAttribute | | Table |
+--------------+ | Table | +-----------------+
-> +-------------------+
/ ^
/ |
+--------------+ +-------------------+
| mvpnInterAs | | mvpnMrouteTable |
| IpmsiTable | +-------------------+
+--------------+
o mvpnIpmsiTable o mvpnIpmsiAdvtTable
This table contains managed objects for monitoring all Intra-AS This table contains managed objects representing advertisements of
I-PMSIs advertised and received by a PE. This table contains all Intra-AS I-PMSIs advertised/received by a PE.
advertised and received Intra-AS I-PMSIs. With PIM-MVPN, it is
applicable only when BGP-Based Autodiscovery of MVPN Membership is
used.
o mvpnInterAsIpmsiTable o mvpnInterAsIpmsiAdvtTable
This table contains managed objects representing advertisements of
Inter-AS I-PMSIs advertised/received by a PE.
This table contains all advertised and received Inter-AS I-PMSIs. o mvpnSpmsiAdvtTable
With PIM-MVPN, it is applicable only when BGP-Based Autodiscovery
of MVPN Membership is used.
o mvpnSpmsiTable This table contains managed objects representing advertisements of
S-PMSIs advertised/received by a PE.
This table contains managed objects for monitoring all S-PMSIs The following two tables are designed for handling routing
advertised and received by a PE. information that is advertised/received by a PE.
o mvpnMrouteTable o mvpnMrouteTable
This table augments This table contains multicast routing information in MVRFs present
ipMcastMIB.ipMcast.ipMcastRouteTable [RFC5132], for some MVPN in a PE.
specific information.
o l2l3VpnMcastPmsiTunnelAttributeTable o mvpnMrouteNextHopTable
An entry of this table corresponds to a PMSI Tunnel attribute and The table contains information on the next-hops on outgoing
is maintained by a PE router that advertises and receives the interfaces for routing IP multicast datagrams in MVPNs present on
attribute. Th entry in this table is referred by entries in a PE.
mvpnIpmsiTable, mvpnInterAsIpmsiTable, mvpnSpmsiTable, and
mvpnMrouteTable.
3.2. MIB Module Definitions 3.2. MIB Module Definitions
MCAST-VPN-MIB DEFINITIONS ::= BEGIN MCAST-VPN-MIB DEFINITIONS ::= BEGIN
IMPORTS IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE,
Gauge32, Unsigned32, mib-2 Counter32, Counter64, Gauge32, Unsigned32, TimeTicks,
zeroDotZero, mib-2
FROM SNMPv2-SMI -- [RFC2578] FROM SNMPv2-SMI -- [RFC2578]
MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
FROM SNMPv2-CONF -- [RFC2580] FROM SNMPv2-CONF -- [RFC2580]
TruthValue, RowPointer, RowStatus, TimeStamp, TimeInterval RowPointer, TimeStamp, TimeInterval
FROM SNMPv2-TC -- [RFC2579] FROM SNMPv2-TC -- [RFC2579]
SnmpAdminString CounterBasedGauge64
FROM SNMP-FRAMEWORK-MIB -- [RFC2571] FROM HCNUM-TC -- [RFC2856]
InterfaceIndex, InterfaceIndexOrZero
FROM IF-MIB -- [RFC2863]
InetAddress, InetAddressType, InetAddressPrefixLength, InetAddress, InetAddressType, InetAddressPrefixLength,
InetAutonomousSystemNumber InetAutonomousSystemNumber
FROM INET-ADDRESS-MIB -- [RFC2851] FROM INET-ADDRESS-MIB -- [RFC2851]
mplsL3VpnVrfName, MplsL3VpnRouteDistinguisher mplsL3VpnVrfName, MplsL3VpnRouteDistinguisher
FROM MPLS-L3VPN-STD-MIB -- [RFC4382] FROM MPLS-L3VPN-STD-MIB -- [RFC4382]
ipMcastRouteEntry IANAipRouteProtocol, IANAipMRouteProtocol
FROM IPMCAST-MIB -- [RFC5132] FROM IANA-RTPROTO-MIB -- [RTPROTO]
L2L3VpnMcastProviderTunnelType L2L3VpnMcastProviderTunnelType
FROM L2L3-VPN-MCAST-TC-MIB; FROM L2L3-VPN-MCAST-TC-MIB;
mvpnMIB MODULE-IDENTITY mvpnMIB MODULE-IDENTITY
LAST-UPDATED "201712081200Z" -- 8th December 2017 12:00:00 GMT LAST-UPDATED "201804301200Z" -- 30th April 2018 12:00:00 GMT
ORGANIZATION "IETF BESS Working Group." ORGANIZATION "IETF BESS Working Group."
CONTACT-INFO CONTACT-INFO
" Zhaohui Zhang " Zhaohui Zhang
Juniper Networks, Inc. Juniper Networks, Inc.
10 Technology Park Drive 10 Technology Park Drive
Westford, MA 01886 Westford, MA 01886
USA USA
Email: zzhang@juniper.net Email: zzhang@juniper.net
Saud Asif Saud Asif
skipping to change at page 8, line 39 skipping to change at page 8, line 14
35-1, Yagiyama Kasumi-cho 35-1, Yagiyama Kasumi-cho
Taihaku-ku, Sendai, 982-8577 Taihaku-ku, Sendai, 982-8577
Japan Japan
Email: tsuno@m.ieice.org Email: tsuno@m.ieice.org
Comments and discussion to bess@ietf.org" Comments and discussion to bess@ietf.org"
DESCRIPTION DESCRIPTION
"This MIB contains managed object definitions for "This MIB contains managed object definitions for
multicast in BGP/MPLS IP VPNs defined by [RFC6513]. multicast in BGP/MPLS IP VPNs defined by [RFC6513].
Copyright (C) The Internet Society (2017)." Copyright (C) The Internet Society (2018)."
-- Revision history. -- Revision history.
REVISION "201712081200Z" -- 8th December, 2017 REVISION "201804301200Z" -- 30th April, 2018
DESCRIPTION DESCRIPTION
"Initial version, published as RFC XXXX." "Initial version, published as RFC XXXX."
-- RFC Ed. replace XXXX with actual RFC number and remove this note -- RFC Ed. replace XXXX with actual RFC number and remove this note
::= { mib-2 YYYY } ::= { mib-2 YYYY }
-- IANA Reg.: Please assign a value for "YYYY" under the -- IANA Reg.: Please assign a value for "YYYY" under the
-- 'mib-2' subtree and record the assignment in the SMI -- 'mib-2' subtree and record the assignment in the SMI
-- Numbers registry. -- Numbers registry.
skipping to change at page 9, line 23 skipping to change at page 8, line 46
mvpnNotifications OBJECT IDENTIFIER ::= { mvpnMIB 0 } mvpnNotifications OBJECT IDENTIFIER ::= { mvpnMIB 0 }
-- tables, scalars -- tables, scalars
mvpnObjects OBJECT IDENTIFIER ::= { mvpnMIB 1 } mvpnObjects OBJECT IDENTIFIER ::= { mvpnMIB 1 }
-- conformance information -- conformance information
mvpnConformance OBJECT IDENTIFIER ::= { mvpnMIB 2 } mvpnConformance OBJECT IDENTIFIER ::= { mvpnMIB 2 }
-- mvpn Objects -- mvpn Objects
mvpnScalars OBJECT IDENTIFIER ::= { mvpnObjects 1 } mvpnScalars OBJECT IDENTIFIER ::= { mvpnObjects 1 }
mvpnGeneral OBJECT IDENTIFIER ::= { mvpnObjects 2 } mvpnGeneric OBJECT IDENTIFIER ::= { mvpnObjects 2 }
mvpnConfig OBJECT IDENTIFIER ::= { mvpnObjects 3 } mvpnConfig OBJECT IDENTIFIER ::= { mvpnObjects 3 }
mvpnStates OBJECT IDENTIFIER ::= { mvpnObjects 4 } mvpnStates OBJECT IDENTIFIER ::= { mvpnObjects 4 }
-- Scalar Objects -- Scalar Objects
mvpnMvrfs OBJECT-TYPE mvpnMvrfs OBJECT-TYPE
SYNTAX Gauge32 SYNTAX Gauge32
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The total number of MVRFs that are present on "The total number of Multicast Virtual Routing and
this Provider Edge router (PE), whether Forwarding tables (MVRFs) that are present on
for IPv4, IPv6, or mLDP C-Multicast." this Provider Edge router (PE). This includes MVRFs
for IPv4, IPv6, and mLDP C-Multicast.
"
::= { mvpnScalars 1 } ::= { mvpnScalars 1 }
mvpnV4Mvrfs OBJECT-TYPE mvpnV4Mvrfs OBJECT-TYPE
SYNTAX Gauge32 SYNTAX Gauge32
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The number of MVRFs for IPv4 C-Multicast that are "The number of MVRFs for IPv4 C-Multicast that are
present in this PE." present in this PE.
"
::= { mvpnScalars 2 } ::= { mvpnScalars 2 }
mvpnV6Mvrfs OBJECT-TYPE mvpnV6Mvrfs OBJECT-TYPE
SYNTAX Gauge32 SYNTAX Gauge32
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The number of MVRFs for IPv6 C-Multicast that are "The number of MVRFs for IPv6 C-Multicast that are
present in this PE." present in this PE.
"
::= { mvpnScalars 3 } ::= { mvpnScalars 3 }
mvpnPimV4Mvrfs OBJECT-TYPE mvpnPimV4Mvrfs OBJECT-TYPE
SYNTAX Gauge32 SYNTAX Gauge32
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The number of PIM-MVPN MVRFs for IPv4 C-Multicast that are "The number of MVRFs of MVPNs that use PIM for
present in this PE." exchanging IPv4 C-Multicast routing information
present in this PE.
"
::= { mvpnScalars 4 } ::= { mvpnScalars 4 }
mvpnPimV6Mvrfs OBJECT-TYPE mvpnPimV6Mvrfs OBJECT-TYPE
SYNTAX Gauge32 SYNTAX Gauge32
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The number of PIM-MVPN MVRFs for IPv6 C-Multicast that are "The number of MVRFs of MVPNs that use PIM for
present in this PE." exchanging IPv6 C-Multicast routing information
present in this PE.
"
::= { mvpnScalars 5 } ::= { mvpnScalars 5 }
mvpnBgpV4Mvrfs OBJECT-TYPE mvpnBgpV4Mvrfs OBJECT-TYPE
SYNTAX Gauge32 SYNTAX Gauge32
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The number of BGP-MVPN MVRFs for IPv4 C-Multicast that are "The number of MVRFs of MVPNs that use BGP for
present in this PE." exchanging IPv4 C-Multicast routing information
present in this PE.
"
::= { mvpnScalars 6 } ::= { mvpnScalars 6 }
mvpnBgpV6Mvrfs OBJECT-TYPE mvpnBgpV6Mvrfs OBJECT-TYPE
SYNTAX Gauge32 SYNTAX Gauge32
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The number of BGP-MVPN MVRFs for IPv6 C-Multicast that are "The number of MVRFs of MVPNs that use BGP for
present in this PE." exchanging IPv6 C-Multicast routing information
present in this PE.
"
::= { mvpnScalars 7 } ::= { mvpnScalars 7 }
mvpnMldpMvrfs OBJECT-TYPE mvpnMldpMvrfs OBJECT-TYPE
SYNTAX Gauge32 SYNTAX Gauge32
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The number of BGP-MVPN MVRFs for mLDP C-Multicast that are "The number of MVRFs of MVPNs that use BGP for
present in this PE." exchanging mLDP C-Multicast routing information
present in this PE.
"
::= { mvpnScalars 8 } ::= { mvpnScalars 8 }
mvpnNotificationEnable OBJECT-TYPE -- Generic MVRF Information Table
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"If this object is TRUE, then the generation of all
notifications defined in this MIB is enabled."
DEFVAL { false }
::= { mvpnScalars 9 }
-- General MVRF Information Table
mvpnGeneralTable OBJECT-TYPE mvpnGenericTable OBJECT-TYPE
SYNTAX SEQUENCE OF MvpnGeneralEntry SYNTAX SEQUENCE OF MvpnGenericEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table specifies the general information about the MVRFs "This table specifies the generic information about the MVRFs
present in this PE." present in this PE.
::= { mvpnGeneral 1 }
mvpnGeneralEntry OBJECT-TYPE Entries in this table are not required to survive a reboot
SYNTAX MvpnGeneralEntry of the managed entity.
"
::= { mvpnGeneric 1 }
mvpnGenericEntry OBJECT-TYPE
SYNTAX MvpnGenericEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An entry in this table is created for each MVRF in the "This entry represents a conceptual row in the mvpnGenericTable.
PE." Each MVRF serviced by the PE will have an entry in this table.
The MVRF represented by this entry will have one or more
corresponding P-Multicast Service Interfaces (PMSIs)
and a corresponding VRF in MPLS-L3VPN-STD-MIB [RFC4382].
"
INDEX { INDEX {
mplsL3VpnVrfName, mplsL3VpnVrfName,
mvpnGenAddressFamily mvpnGenAddressFamily
} }
::= { mvpnGeneralTable 1 } ::= { mvpnGenericTable 1 }
MvpnGeneralEntry ::= SEQUENCE { MvpnGenericEntry ::= SEQUENCE {
mvpnGenAddressFamily INTEGER, mvpnGenAddressFamily INTEGER,
mvpnGenMvrfStatusChange INTEGER, mvpnGenMvrfLastOperation INTEGER,
mvpnGenMvrfStatusChangeTime TimeStamp, mvpnGenMvrfLastOperationTime TimeStamp,
mvpnGenCmcastRouteProtocol INTEGER, mvpnGenCmcastRouteProtocol INTEGER,
mvpnGenIpmsiConfig RowPointer, mvpnGenIpmsiInfo RowPointer,
mvpnGenInterAsPmsiConfig RowPointer, mvpnGenInterAsPmsiInfo RowPointer,
mvpnGenUmhSelection INTEGER, mvpnGenUmhSelection INTEGER,
mvpnGenSiteType INTEGER, mvpnGenCustomerSiteType INTEGER,
mvpnGenSptnlLimit Unsigned32, mvpnGenSPTunnelLimit Unsigned32
mvpnGenRowStatus RowStatus
} }
mvpnGenAddressFamily OBJECT-TYPE mvpnGenAddressFamily OBJECT-TYPE
SYNTAX INTEGER { SYNTAX INTEGER {
ipv4(1), ipv4(1),
ipv6(2) ipv6(2)
} }
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The Address Family that this entry is for" "The Address Family of the MVRF represented by this entry"
::= { mvpnGeneralEntry 1 } REFERENCE
"RFC6513, Section 1
"
::= { mvpnGenericEntry 1 }
mvpnGenMvrfStatusChange OBJECT-TYPE mvpnGenMvrfLastOperation OBJECT-TYPE
SYNTAX INTEGER { SYNTAX INTEGER {
createdMvrf(1), createdMvrf(1),
deletedMvrf(2), deletedMvrf(2),
modifiedMvrfIpmsiConfig(3), modifiedMvrfIpmsiConfig(3),
modifiedMvrfSpmsiConfig(4) modifiedMvrfSpmsiConfig(4)
} }
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object describes the last status change that "This object describes the last operation pertaining
happened for the given MVRF. to the MVRF represented by this entry.
createdMvrf(1): createdMvrf(1):
indicates that the MVRF was created in the PE. the MVRF was created in the PE.
deletedMvrf(2): deletedMvrf(2):
indicates that the MVRF was deleted from the PE. the MVRF was deleted from the PE.
A row in this table will never have A row in this table will never have
mvpnGenMvrfStatusChange equal to deletedMvrf(2), mvpnGenMvrfLastOperation equal to deletedMvrf(2),
because in that case the row itself will be deleted because in that case the row itself will be deleted
from the table. from the table.
This value for mvpnGenMvrfStatusChange is defined mainly This value for mvpnGenMvrfLastOperation is defined
for use in mvpnMvrfStatusChange notification. mainly for use in mvpnMvrfOperationChange notification.
modifiedMvrfIpmsiConfig(3): modifiedMvrfIpmsiConfig(3):
indicates that the I-PMSI for the MVRF was configured, an I-PMSI for the MVRF was configured,
deleted or changed. deleted or changed.
modifiedMvrfSpmsiConfig(4): modifiedMvrfSpmsiConfig(4):
indicates that the S-PMSI for the MVRF was configured, an S-PMSI for the MVRF was configured,
deleted or changed. deleted or changed.
" "
DEFVAL { createdMvrf } DEFVAL { createdMvrf }
::= { mvpnGeneralEntry 2 } ::= { mvpnGenericEntry 2 }
mvpnGenMvrfStatusChangeTime OBJECT-TYPE mvpnGenMvrfLastOperationTime OBJECT-TYPE
SYNTAX TimeStamp SYNTAX TimeStamp
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The time at which the last status change for the MVRF in "The time at which the last operation for the MVRF in
question took place. The last operational change is specified question took place. The last operational change is specified
by mvpnGenMvrfStatusChange. by mvpnGenMvrfLastOperation.
The time at which the last operation, specifed
in mvpnGenMvrfLastOperation, for the MVRF
represented by this entry was carried out.
" "
::= { mvpnGeneralEntry 3 }
::= { mvpnGenericEntry 3 }
mvpnGenCmcastRouteProtocol OBJECT-TYPE mvpnGenCmcastRouteProtocol OBJECT-TYPE
SYNTAX INTEGER { SYNTAX INTEGER {
pim (1), pim (1),
bgp (2) bgp (2)
} }
MAX-ACCESS read-create MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The protocol used to signal C-multicast states across the "The protocol used to signal C-multicast routing
provider core. information across the provider core.
pim(1): PIM (PIM-MVPN). PIM (PIM-MVPN): pim(1)
bgp(2): BGP (BGP-MVPN). BGP (BGP-MVPN): bgp(2)
" "
::= { mvpnGeneralEntry 4 } REFERENCE
"RFC6513, Section 5"
::= { mvpnGenericEntry 4 }
mvpnGenIpmsiConfig OBJECT-TYPE mvpnGenIpmsiInfo OBJECT-TYPE
SYNTAX RowPointer SYNTAX RowPointer
MAX-ACCESS read-create MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This points to a row in mvpnPmsiConfigTable, "This points to a conceptual row representing
for I-PMSI configuration. the corresponding I-PMSI in mvpnPmsiTable.
If there is no I-PMSI for the MVRF, the
value of this object will be zeroDotZero.
" "
::= { mvpnGeneralEntry 5 } DEFVAL { zeroDotZero }
::= { mvpnGenericEntry 5 }
mvpnGenInterAsPmsiConfig OBJECT-TYPE mvpnGenInterAsPmsiInfo OBJECT-TYPE
SYNTAX RowPointer SYNTAX RowPointer
MAX-ACCESS read-create MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This points to a row in mvpnPmsiConfigTable, "This points to a conceptual row representing
for inter-as I-PMSI configuration, in case of segmented the corresponding Inter-AS I-PMSI in mvpnPmsiTable,
inter-as provider tunnels. in case of segmented Inter-AS provider tunnels.
If there is no segmented Inter-AS I-PMSI for the MVRF,
the value of this object will be zeroDotZero.
" "
::= { mvpnGeneralEntry 6 } DEFVAL { zeroDotZero }
::= { mvpnGenericEntry 6 }
mvpnGenUmhSelection OBJECT-TYPE mvpnGenUmhSelection OBJECT-TYPE
SYNTAX INTEGER { SYNTAX INTEGER {
highestPeAddress (1), highestPeAddress (1),
cRootGroupHashing (2), cRootGroupHashing (2),
ucastUmhRoute (3) ucastUmhRoute (3)
} }
MAX-ACCESS read-create MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The UMH selection method for this mvpn, as specified in "The UMH selection method for this mvpn, as specified in
section 5.1.3 of [RFC6513]: section 5.1.3 of [RFC6513]:
highestPeAddress (1): PE with the highest address PE with the highest address: highestPeAddress (1)
cRootGroupHashing (2): hashing based on (c-root, c-group) hashing based on (c-root, c-group): cRootGroupHashing (2)
uncastUmhRoute (3): per ucast route towards c-root per ucast route towards c-root: ucastUmhRoute (3)
" "
::= { mvpnGeneralEntry 7 } REFERENCE
"RFC6513, Section 5.1"
::= { mvpnGenericEntry 7 }
mvpnGenSiteType OBJECT-TYPE mvpnGenCustomerSiteType OBJECT-TYPE
SYNTAX INTEGER { SYNTAX INTEGER {
senderReceiver (1), senderReceiver (1),
receiverOnly (2), receiverOnly (2),
senderOnly (3) senderOnly (3)
} }
MAX-ACCESS read-create MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Whether this site is a receiver-only site or not. "The type of a customer site, which is connected to
senderReceiver (1): both sender and receiver site. this PE, in the MVPN which has the MVRF represented
receiverOnly (2): receiver-only site. by this entry.
senderOnly (3): sender-only site.
Site is both sender and receiver: senderReceiver (1)
Site is receiver-only : receiverOnly (2)
Site is sender-only : senderOnly (3)
" "
::= { mvpnGeneralEntry 8 } REFERENCE
"RFC6513, Section 2.3"
::= { mvpnGenericEntry 8 }
mvpnGenSptnlLimit OBJECT-TYPE mvpnGenSPTunnelLimit OBJECT-TYPE
SYNTAX Unsigned32 SYNTAX Unsigned32
MAX-ACCESS read-create MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The max number of selective provider tunnels this PE "The maximum number of selective provider tunnels that
allows for this mvpn." this PE allows for this MVPN.
::= { mvpnGeneralEntry 9 } "
REFERENCE
"RFC6513, Section 13"
mvpnGenRowStatus OBJECT-TYPE ::= { mvpnGenericEntry 9 }
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This is used to create or delete a row in this table."
::= { mvpnGeneralEntry 10 }
-- General BGP-MVPN table -- Generic BGP-MVPN table
mvpnBgpGeneralTable OBJECT-TYPE mvpnBgpGenericTable OBJECT-TYPE
SYNTAX SEQUENCE OF MvpnBgpGeneralEntry SYNTAX SEQUENCE OF MvpnBgpGenericEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table augments the mvpnGeneralTable and is for BGP-MVPN "This table specifies the specific information of MVRFs of MVPNs
specific information. that use BGP for exchanging C-Multicast routing information
present in this PE.
" "
::= { mvpnGeneral 2 } ::= { mvpnGeneric 2 }
mvpnBgpGeneralEntry OBJECT-TYPE mvpnBgpGenericEntry OBJECT-TYPE
SYNTAX MvpnBgpGeneralEntry SYNTAX MvpnBgpGenericEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The mvpnBgpGeneralEntry matches and augments an "This entry represents a conceptual row in the mvpnBgpGenericTable.
mvpnGeneralEntry for a BGP-MVPN instance, with BGP-MVPN Each MVRF of an MVPN that use BGP for exchanging C-Multicast
specific informatoin. routing information will have an entry in this table.
The MVRF represented by this entry will have
a corresponding entry in the mvpnGenericTable.
" "
AUGMENTS { mvpnGeneralEntry } INDEX {
::= { mvpnBgpGeneralTable 1 } mplsL3VpnVrfName,
mvpnGenAddressFamily
}
::= { mvpnBgpGenericTable 1 }
MvpnBgpGeneralEntry ::= SEQUENCE { MvpnBgpGenericEntry ::= SEQUENCE {
mvpnBgpGenMode INTEGER, mvpnBgpGenMode INTEGER,
mvpnBgpGenVrfRtImport MplsL3VpnRouteDistinguisher, mvpnBgpGenVrfRouteImport MplsL3VpnRouteDistinguisher,
mvpnBgpGenSrcAs InetAutonomousSystemNumber mvpnBgpGenSrcAs InetAutonomousSystemNumber,
mvpnBgpGenCmcastRouteWithdrawalTimer Unsigned32,
mvpnBgpGenSrcSharedTreeJoinTimer Unsigned32,
mvpnBgpGenMsgRateLimit Unsigned32,
mvpnBgpGenMaxSpmsiAdRoutes Unsigned32,
mvpnBgpGenMaxSpmsiAdRouteFreq Unsigned32,
mvpnBgpGenMaxSrcActiveAdRoutes Unsigned32,
mvpnBgpGenMaxSrcActiveAdRouteFreq Unsigned32
} }
mvpnBgpGenMode OBJECT-TYPE mvpnBgpGenMode OBJECT-TYPE
SYNTAX INTEGER { SYNTAX INTEGER {
rptSpt (1), rptSpt (1),
sptOnly (2) sptOnly (2)
} }
MAX-ACCESS read-write MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"For two different BGP-MVPN modes: "For two different BGP-MVPN modes:
rptSpt(1): inter-site shared tree mode rptSpt(1): inter-site shared tree mode
sptOnly(2): inter-site source-only tree mode. sptOnly(2): inter-site source-only tree mode.
" "
::= { mvpnBgpGeneralEntry 1} REFERENCE
"RFC6513, Section 9.3.1"
::= { mvpnBgpGenericEntry 1 }
mvpnBgpGenVrfRtImport OBJECT-TYPE mvpnBgpGenVrfRouteImport OBJECT-TYPE
SYNTAX MplsL3VpnRouteDistinguisher SYNTAX MplsL3VpnRouteDistinguisher
MAX-ACCESS read-write MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The VRF Route Import Extended Community that this PE "The VRF Route Import Extended Community that this PE
adds to unicast vpn routes that it advertises for this mvpn. adds to unicast VPN routes that it advertises for this MVPN.
" "
REFERENCE REFERENCE
"RFC4364, Section 4.2 "RFC6514, Section 7
RFC4382, Section 7
" "
::= { mvpnBgpGeneralEntry 2} ::= { mvpnBgpGenericEntry 2 }
mvpnBgpGenSrcAs OBJECT-TYPE mvpnBgpGenSrcAs OBJECT-TYPE
SYNTAX InetAutonomousSystemNumber SYNTAX InetAutonomousSystemNumber
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The Source AS number in Source AS Extended Community that this "The Source AS number in Source AS Extended Community that this
PE adds to the unicast vpn routes that it advertises for PE adds to the unicast VPN routes that it advertises for
this mvpn. this MVPN.
" "
::= { mvpnBgpGeneralEntry 3} REFERENCE
"RFC6514, Section 6
"
::= { mvpnBgpGenericEntry 3 }
-- PMSI Configuration Table mvpnBgpGenCmcastRouteWithdrawalTimer OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The configurable timer to control the delay
for the advertisement of withdrawals of
C-multicast routes.
mvpnPmsiConfigTable OBJECT-TYPE "
SYNTAX SEQUENCE OF MvpnPmsiConfigEntry REFERENCE
MAX-ACCESS not-accessible "RFC6514, Section 16.1.1"
::= { mvpnBgpGenericEntry 4 }
mvpnBgpGenSrcSharedTreeJoinTimer OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table specifies the configured PMSIs." "The configurable timer to control the delay
::= { mvpnConfig 1 } for the advertisement of Source/Shared Tree Join
C-multicast routes.
"
REFERENCE
"RFC6514, Section 16.1.2"
::= { mvpnBgpGenericEntry 5 }
mvpnPmsiConfigEntry OBJECT-TYPE mvpnBgpGenMsgRateLimit OBJECT-TYPE
SYNTAX MvpnPmsiConfigEntry SYNTAX Unsigned32
MAX-ACCESS not-accessible MAX-ACCESS read-write
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An entry in this table is created for each PMSI configured "The upper bounds on rate of BGP message exchange among PEs
on this router. It can be referred to by either I-PMSI for exchanging C-multicast routing information
configuration (in mvpnGeneralEntry) or S-PMSI configuration
(in mvpnSpmsiConfigEntry)
" "
INDEX { REFERENCE
mvpnPmsiConfigTunnelType, "RFC6514, Section 17"
mvpnPmsiConfigTunnelAuxInfo, ::= { mvpnBgpGenericEntry 6 }
mvpnPmsiConfigTunnelPimGroupAddrType,
mvpnPmsiConfigTunnelPimGroupAddr,
mvpnPmsiConfigTunnelOrTemplateName
}
::= { mvpnPmsiConfigTable 1 } mvpnBgpGenMaxSpmsiAdRoutes OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The upper bound on the number of S-PMSI A-D routes.
"
REFERENCE
"RFC6514, Section 17"
::= { mvpnBgpGenericEntry 7 }
MvpnPmsiConfigEntry ::= SEQUENCE { mvpnBgpGenMaxSpmsiAdRouteFreq OBJECT-TYPE
mvpnPmsiConfigTunnelType SYNTAX Unsigned32
L2L3VpnMcastProviderTunnelType, MAX-ACCESS read-write
mvpnPmsiConfigTunnelAuxInfo Unsigned32, STATUS current
mvpnPmsiConfigTunnelPimGroupAddrType DESCRIPTION
InetAddressType, "The upper bound on how frequently S-PMSI A-D routes
mvpnPmsiConfigTunnelPimGroupAddr may be generated.
InetAddress,
mvpnPmsiConfigTunnelOrTemplateName
SnmpAdminString,
mvpnPmsiConfigEncapsType INTEGER,
mvpnPmsiConfigRowStatus RowStatus
}
mvpnPmsiConfigTunnelType OBJECT-TYPE "
SYNTAX L2L3VpnMcastProviderTunnelType REFERENCE
MAX-ACCESS not-accessible "RFC6514, Section 17"
::= { mvpnBgpGenericEntry 8 }
mvpnBgpGenMaxSrcActiveAdRoutes OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Type of tunnel used to instantiate the PMSI." "The upper bound on the number of Source Active A-D routes.
::= { mvpnPmsiConfigEntry 1 } "
REFERENCE
"RFC6514, Section 17"
::= { mvpnBgpGenericEntry 9 }
mvpnPmsiConfigTunnelAuxInfo OBJECT-TYPE mvpnBgpGenMaxSrcActiveAdRouteFreq OBJECT-TYPE
SYNTAX Unsigned32 SYNTAX Unsigned32
MAX-ACCESS not-accessible MAX-ACCESS read-write
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Additional tunnel information depending on the value of "The upper bound on how frequently Source Active A-D routes
mvpnPmsiConfigTunnelType object. may be generated.
"
REFERENCE
"RFC6514, Section 17"
::= { mvpnBgpGenericEntry 10 }
pimSsm(3), pimAsm(4), pimBidir(5): -- PMSI Configuration Table
In case of S-PMSI, number of groups starting at
mvpnPmsiConfigTunnelPimGroupAddress.
This allows a range of PIM provider tunnel
group addresses to be specified in S-PMSI case.
In I-PMSI case, it must be 1.
rsvpP2mp(1): mvpnPmsiTable OBJECT-TYPE
1 for statically specified rsvp-p2mp tunnel SYNTAX SEQUENCE OF MvpnPmsiEntry
2 for dynamically created rsvp-p2mp tunnel MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table corresponds to
the attribute information of a specific
PMSI configured on a PE router.
"
::= { mvpnConfig 1 }
mvpnPmsiEntry OBJECT-TYPE
SYNTAX MvpnPmsiEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row corresponding to a specific
PMSI on this router.
ingressReplication(6):
1 for using any existing p2p/mp2p LSP
2 for dynamically creating new p2p LSP
" "
INDEX {
mvpnPmsiTunnelIfIndex
}
::= { mvpnPmsiTable 1 }
::= { mvpnPmsiConfigEntry 2 } MvpnPmsiEntry ::= SEQUENCE {
mvpnPmsiTunnelIfIndex InterfaceIndex,
mvpnPmsiTunnelType L2L3VpnMcastProviderTunnelType,
mvpnPmsiTunnelPimGroupAddrType InetAddressType,
mvpnPmsiTunnelPimGroupAddr InetAddress,
mvpnPmsiEncapsulationType INTEGER
}
mvpnPmsiConfigTunnelPimGroupAddrType OBJECT-TYPE mvpnPmsiTunnelIfIndex OBJECT-TYPE
SYNTAX InetAddressType SYNTAX InterfaceIndex
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"In case of PIM provider tunnel, the type of tunnel address." "This is a unique index for an entry in the
::= { mvpnPmsiConfigEntry 3 } mvpnPmsiTable. A non-zero index for an
entry indicates the ifIndex for the corresponding
entry of PMSI in the ifTable.
"
REFERENCE
"RFC2863
"
::= { mvpnPmsiEntry 1 }
mvpnPmsiConfigTunnelPimGroupAddr OBJECT-TYPE mvpnPmsiTunnelType OBJECT-TYPE
SYNTAX InetAddress SYNTAX L2L3VpnMcastProviderTunnelType
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"In case of PIM provider tunnel, the provider tunnel address." "This object indicates the type of tunnel used to
::= { mvpnPmsiConfigEntry 4 } instantiate the PMSI corresponding to this entry"
REFERENCE
"RFC6513 Sec. 2.6
"
::= { mvpnPmsiEntry 2 }
mvpnPmsiConfigTunnelOrTemplateName OBJECT-TYPE mvpnPmsiTunnelPimGroupAddrType OBJECT-TYPE
SYNTAX SnmpAdminString SYNTAX InetAddressType
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The tunnel name or template name used to create tunnels. "When the PIM provider tunnel is used for instantiating
The value of this object depends on the values of the PMSI corresponding to this entry, i.e.,
mvpnPmsiConfigTunnelType and mvpnPmsiConfigTunnelAuxInfo the value of mvpnPmsiTunnelType is
objects: pimSsm(3), pimAsm(4), or pimBidir(5),
this object indicates the type of tunnel address.
Otherwise, the value of this object will be
unknown(0).
"
::= { mvpnPmsiEntry 3 }
dynamically created rsvp-p2mp tunnel: template name mvpnPmsiTunnelPimGroupAddr OBJECT-TYPE
statically specified rsvp-p2mp tunnel: tunnel name SYNTAX InetAddress
ingress-replication using MAX-ACCESS not-accessible
dynamically created LSPs: template name STATUS current
other: null DESCRIPTION
"When the PIM provider tunnel is used for instantiating
the PMSI corresponding to this entry, i.e.,
the value of mvpnPmsiTunnelType is
pimSsm(3), pimAsm(4), or pimBidir(5),
this object indicates the tunnel address.
Otherwise, the value of this object will be
a string of length zero.
" "
::= { mvpnPmsiConfigEntry 5 } ::= { mvpnPmsiEntry 4 }
mvpnPmsiConfigEncapsType OBJECT-TYPE mvpnPmsiEncapsulationType OBJECT-TYPE
SYNTAX INTEGER { SYNTAX INTEGER {
greIp (1), greIp (1),
ipIp (2), ipIp (2),
mpls (3) mpls (3)
} }
MAX-ACCESS read-create MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The encapsulation type to be used, in case of PIM tunnel or "The encapsulation type to be used for sending
ingress-replication. packets through a P-tunnel.
"
::= { mvpnPmsiConfigEntry 6 } The enumerated values and the corresponding
encapsulation types are as follows:
mvpnPmsiConfigRowStatus OBJECT-TYPE greIp (0) : GRE (Generic Routing Encapsulation) encapsulation [RFC2784]
SYNTAX RowStatus ipIp (1) : IP-in-IP encapsulation [RFC2003]
MAX-ACCESS read-create mpls (2) : MPLS encapsulation [RFC3032]
STATUS current "
DESCRIPTION REFERENCE
"Used to create/modify/delete a row in this table." "RFC2003
::= { mvpnPmsiConfigEntry 7 } RFC2784
RFC3032
RFC6513 Sec. 12.1
"
::= { mvpnPmsiEntry 5 }
-- S-PMSI configuration table -- S-PMSI configuration table
mvpnSpmsiConfigTable OBJECT-TYPE mvpnSpmsiTable OBJECT-TYPE
SYNTAX SEQUENCE OF MvpnSpmsiConfigEntry SYNTAX SEQUENCE OF MvpnSpmsiEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table specifies S-PMSI configuration." "An entry in this table corresponds to
a specific S-PMSI configured on a PE router.
This table stores only S-PMSI specific
attribute information and generic attribute
information of the S-PMSI is stored in
mvpnPmsiTable.
Therefore, there MUST be corresponding entry
that pertains to the S-PMSI, in mvpnPmsiTable.
"
::= { mvpnConfig 2 } ::= { mvpnConfig 2 }
mvpnSpmsiConfigEntry OBJECT-TYPE mvpnSpmsiEntry OBJECT-TYPE
SYNTAX MvpnSpmsiConfigEntry SYNTAX MvpnSpmsiEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An entry is created for each S-PMSI configuration." "A conceptual row corresponding to a specific
S-PMSI on this router.
Implementers need to be aware that there are quite a few
index objects that together can exceed the size allowed
for an Object Identifier (OID). So implementers must make
sure that OIDs of column instances in this table will have
no more than 128 sub-identifiers, otherwise they cannot be
accessed using SNMPv1, SNMPv2c, or SNMPv3.
"
INDEX { INDEX {
mplsL3VpnVrfName, mplsL3VpnVrfName,
mvpnSpmsiConfigCmcastAddrType, mvpnSpmsiCmcastAddrType,
mvpnSpmsiConfigCmcastGroupAddr, mvpnSpmsiCmcastGroupAddr,
mvpnSpmsiConfigCmcastGroupPrefixLen, mvpnSpmsiCmcastGroupPrefixLen,
mvpnSpmsiConfigCmcastSourceAddr, mvpnSpmsiCmcastSourceAddr,
mvpnSpmsiConfigCmcastSourcePrefixLen mvpnSpmsiCmcastSourcePrefixLen
} }
::= { mvpnSpmsiConfigTable 1 } ::= { mvpnSpmsiTable 1 }
MvpnSpmsiConfigEntry ::= SEQUENCE { MvpnSpmsiEntry ::= SEQUENCE {
mvpnSpmsiConfigCmcastAddrType InetAddressType, mvpnSpmsiCmcastAddrType InetAddressType,
mvpnSpmsiConfigCmcastGroupAddr InetAddress, mvpnSpmsiCmcastGroupAddr InetAddress,
mvpnSpmsiConfigCmcastGroupPrefixLen InetAddressPrefixLength, mvpnSpmsiCmcastGroupPrefixLen InetAddressPrefixLength,
mvpnSpmsiConfigCmcastSourceAddr InetAddress, mvpnSpmsiCmcastSourceAddr InetAddress,
mvpnSpmsiConfigCmcastSourcePrefixLen InetAddressPrefixLength, mvpnSpmsiCmcastSourcePrefixLen InetAddressPrefixLength,
mvpnSpmsiConfigThreshold Unsigned32, mvpnSpmsiThreshold Unsigned32,
mvpnSpmsiConfigPmsiPointer RowPointer, mvpnSpmsiPmsiPointer RowPointer
mvpnSpmsiConfigRowStatus RowStatus
} }
mvpnSpmsiConfigCmcastAddrType OBJECT-TYPE mvpnSpmsiCmcastAddrType OBJECT-TYPE
SYNTAX InetAddressType SYNTAX InetAddressType
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Type of C-multicast address" "Type of C-multicast source and group addresses of
::= { mvpnSpmsiConfigEntry 1 } a particular C-flow which is assigned to an S-PMSI
corresponding to this entry."
::= { mvpnSpmsiEntry 1 }
mvpnSpmsiConfigCmcastGroupAddr OBJECT-TYPE mvpnSpmsiCmcastGroupAddr OBJECT-TYPE
SYNTAX InetAddress SYNTAX InetAddress
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"C-multicast group address" "A group address of a particular C-flow which is
::= { mvpnSpmsiConfigEntry 2 } assigned to an S-PMSI corresponding to this entry."
::= { mvpnSpmsiEntry 2 }
mvpnSpmsiConfigCmcastGroupPrefixLen OBJECT-TYPE mvpnSpmsiCmcastGroupPrefixLen OBJECT-TYPE
SYNTAX InetAddressPrefixLength SYNTAX InetAddressPrefixLength
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"C-multicast group address prefix length. "A prefix length of mvpnSpmsiCmcastGroupAddr.
A group 0 (or ::0) with prefix length 32 (or 128) A group 0 (or ::0) with prefix length 32 (or 128)
indicates wildcard group, while a group 0 (or ::0) indicates wildcard group, while a group 0 (or ::0)
with prefix length 0 indicates any group. with prefix length 0 indicates any group.
" "
::= { mvpnSpmsiConfigEntry 3 } ::= { mvpnSpmsiEntry 3 }
mvpnSpmsiConfigCmcastSourceAddr OBJECT-TYPE mvpnSpmsiCmcastSourceAddr OBJECT-TYPE
SYNTAX InetAddress SYNTAX InetAddress
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"C-multicast source address" "A source address of a particular C-flow which is
::= { mvpnSpmsiConfigEntry 4 } assigned to an S-PMSI corresponding to this entry."
::= { mvpnSpmsiEntry 4 }
mvpnSpmsiConfigCmcastSourcePrefixLen OBJECT-TYPE mvpnSpmsiCmcastSourcePrefixLen OBJECT-TYPE
SYNTAX InetAddressPrefixLength SYNTAX InetAddressPrefixLength
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"C-multicast source address prefix length. "A prefix length of mvpnSpmsiCmcastSourceAddr.
A source 0 (or ::0) with prefix length 32 (or 128) A source 0 (or ::0) with prefix length 32 (or 128)
indicates a wildcard source, while a source 0 (or ::0) indicates a wildcard source, while a source 0 (or ::0)
with prefix length 0 indicates any source. with prefix length 0 indicates any source.
" "
::= { mvpnSpmsiConfigEntry 5 } ::= { mvpnSpmsiEntry 5 }
mvpnSpmsiConfigThreshold OBJECT-TYPE mvpnSpmsiThreshold OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295) SYNTAX Unsigned32 (0..4294967295)
UNITS "kilobits per second" UNITS "kilobits per second"
MAX-ACCESS read-create MAX-ACCESS read-write
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The bandwidth threshold value which when exceeded for a "The bandwidth threshold value which when exceeded for a
multicast routing entry in the given MVRF, triggers usage multicast routing entry in the given MVRF, triggers usage
of S-PMSI. of S-PMSI.
" "
::= { mvpnSpmsiConfigEntry 6 } REFERENCE
"RFC6513 Sec. 7.2"
::= { mvpnSpmsiEntry 6 }
mvpnSpmsiConfigPmsiPointer OBJECT-TYPE mvpnSpmsiPmsiPointer OBJECT-TYPE
SYNTAX RowPointer SYNTAX RowPointer
MAX-ACCESS read-create MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This points to a row in mvpnPmsiConfigTable, "This points to a row in mvpnPmsiTable,
to specify tunnel attributes. to specify tunnel attributes.
" "
::= { mvpnSpmsiConfigEntry 7 } ::= { mvpnSpmsiEntry 7 }
mvpnSpmsiConfigRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Used to create/modify/delete a row in this table."
::= { mvpnSpmsiConfigEntry 8 }
-- Table of intra-as I-PMSIs advertised/received -- Table of intra-as I-PMSIs advertised/received
mvpnIpmsiTable OBJECT-TYPE mvpnIpmsiAdvtTable OBJECT-TYPE
SYNTAX SEQUENCE OF MvpnIpmsiEntry SYNTAX SEQUENCE OF MvpnIpmsiAdvtEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table is for all advertised/received I-PMSI "This table is for all advertised/received I-PMSI
advertisements. advertisements.
" "
::= { mvpnStates 1 } ::= { mvpnStates 1 }
mvpnIpmsiEntry OBJECT-TYPE mvpnIpmsiAdvtEntry OBJECT-TYPE
SYNTAX MvpnIpmsiEntry SYNTAX MvpnIpmsiAdvtEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An entry in this table corresponds to an I-PMSI "An entry in this table corresponds to an I-PMSI
advertisement that is advertised/received on this router. advertisement that is advertised/received by this router.
This represents all the sender PEs in the MVPN, This represents all the sender PEs in the MVPN,
with the provider tunnel they use to send traffic. with the provider tunnel they use to send traffic.
Implementers need to be aware that there are quite a few
index objects that together can exceed the size allowed
for an Object Identifier (OID). So implementers must make
sure that OIDs of column instances in this table will have
no more than 128 sub-identifiers, otherwise they cannot be
accessed using SNMPv1, SNMPv2c, or SNMPv3.
" "
INDEX { INDEX {
mplsL3VpnVrfName, mplsL3VpnVrfName,
mvpnIpmsiAfi, mvpnIpmsiAdvtAfi,
mvpnIpmsiRD, mvpnIpmsiAdvtRD,
mvpnIpmsiOrigAddrType, mvpnIpmsiAdvtOrigAddrType,
mvpnIpmsiOrigAddr mvpnIpmsiAdvtOrigAddr
} }
::= { mvpnIpmsiTable 1 } ::= { mvpnIpmsiAdvtTable 1 }
MvpnIpmsiEntry ::= SEQUENCE { MvpnIpmsiAdvtEntry ::= SEQUENCE {
mvpnIpmsiAfi INTEGER, mvpnIpmsiAdvtAfi INTEGER,
mvpnIpmsiRD MplsL3VpnRouteDistinguisher, mvpnIpmsiAdvtRD MplsL3VpnRouteDistinguisher,
mvpnIpmsiOrigAddrType InetAddressType, mvpnIpmsiAdvtOrigAddrType InetAddressType,
mvpnIpmsiOrigAddr InetAddress, mvpnIpmsiAdvtOrigAddr InetAddress,
mvpnIpmsiUpTime TimeInterval, mvpnIpmsiAdvtTunnelAttribute RowPointer,
mvpnIpmsiAttribute RowPointer mvpnIpmsiAdvtReceived Counter32,
mvpnIpmsiAdvtReceivedError Counter32,
mvpnIpmsiAdvtMalformedTunnelType Counter32,
mvpnIpmsiAdvtMalformedTunnelId Counter32,
mvpnIpmsiAdvtLastReceivedTime TimeStamp,
mvpnIpmsiAdvtCounterDiscontinuityTime TimeStamp
} }
mvpnIpmsiAfi OBJECT-TYPE mvpnIpmsiAdvtAfi OBJECT-TYPE
SYNTAX INTEGER { SYNTAX INTEGER {
ipv4(1), ipv4(1),
ipv6(2) ipv6(2)
} }
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The address family this I-PMSI is for." "The address family this I-PMSI is for."
::= { mvpnIpmsiEntry 1 }
mvpnIpmsiRD OBJECT-TYPE ::= { mvpnIpmsiAdvtEntry 1 }
mvpnIpmsiAdvtRD OBJECT-TYPE
SYNTAX MplsL3VpnRouteDistinguisher SYNTAX MplsL3VpnRouteDistinguisher
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The Route Distinguisher in this I-PMSI." "The Route Distinguisher in this I-PMSI."
::= { mvpnIpmsiEntry 2 } ::= { mvpnIpmsiAdvtEntry 2 }
mvpnIpmsiOrigAddrType OBJECT-TYPE mvpnIpmsiAdvtOrigAddrType OBJECT-TYPE
SYNTAX InetAddressType SYNTAX InetAddressType
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The Internet address type of mvpnIpmsiOrigAddr." "The Internet address type of mvpnIpmsiAdvtOrigAddr."
::= { mvpnIpmsiEntry 3 } ::= { mvpnIpmsiAdvtEntry 3 }
mvpnIpmsiOrigAddr OBJECT-TYPE mvpnIpmsiAdvtOrigAddr OBJECT-TYPE
SYNTAX InetAddress SYNTAX InetAddress
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The BGP address of the PE that originated the I-PMSI." "The BGP address of the PE that originated the I-PMSI."
::= { mvpnIpmsiEntry 4 } ::= { mvpnIpmsiAdvtEntry 4 }
mvpnIpmsiUpTime OBJECT-TYPE mvpnIpmsiAdvtTunnelAttribute OBJECT-TYPE
SYNTAX TimeInterval SYNTAX RowPointer
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The time since this I-PMSI "Points to a row in the l2L3VpnMcastPmsiTunnelAttributeTable."
was first advertised/received by the PE. ::= { mvpnIpmsiAdvtEntry 5 }
mvpnIpmsiAdvtReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of I-PMSI advertisements received by the PE router.
This includes advertisements that were discarded.
Discontinuities in the value of this counter can
occur at re-initialization of the management system,
and at other times as indicated by the value of
mvpnIpmsiAdvtCounterDiscontinuityTime.
" "
::= { mvpnIpmsiEntry 5 } ::= { mvpnIpmsiAdvtEntry 6 }
mvpnIpmsiAttribute OBJECT-TYPE mvpnIpmsiAdvtReceivedError OBJECT-TYPE
SYNTAX RowPointer SYNTAX Counter32
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Points to a row in the l2L3VpnMcastPmsiTunnelAttributeTable." "The total number of errors in the I-PMSI advertisements
::= { mvpnIpmsiEntry 6 } received by the PE router.
The value of this object is the sum of
the values of mvpnIpmsiAdvtMalformedTunnelType and
mvpnIpmsiAdvtMalformedTunnelId.
Discontinuities in the value of this counter can
occur at re-initialization of the management system,
and at other times as indicated by the value of
mvpnIpmsiAdvtCounterDiscontinuityTime.
"
::= { mvpnIpmsiAdvtEntry 7 }
mvpnIpmsiAdvtMalformedTunnelType OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of received I-PMSI advertisements that
contain a PMSI Tunnel attribute whose Tunnel
Type field has an undefined tunnel type.
Discontinuities in the value of this counter can
occur at re-initialization of the management system,
and at other times as indicated by the value of
mvpnIpmsiAdvtCounterDiscontinuityTime.
"
REFERENCE
"RFC6514 Sec.5"
::= { mvpnIpmsiAdvtEntry 8 }
mvpnIpmsiAdvtMalformedTunnelId OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of received I-PMSI advertisements that
contain a PMSI Tunnel attribute whose Tunnel
Identifier field cannot be parsed as a
tunnel identifier of the tunnel types specified in
the Tunnel type field of the attribute.
Discontinuities in the value of this counter can
occur at re-initialization of the management system,
and at other times as indicated by the value of
mvpnIpmsiAdvtCounterDiscontinuityTime.
"
REFERENCE
"RFC6514 Sec.5"
::= { mvpnIpmsiAdvtEntry 9 }
mvpnIpmsiAdvtLastReceivedTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when the last I-PMSI
advertisement was received by the PE router.
"
::= { mvpnIpmsiAdvtEntry 10 }
mvpnIpmsiAdvtCounterDiscontinuityTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime on the most recent occasion
at which any one or more of this syslog application's
counters, viz., counters with OID prefix
'mvpnIpmsiAdvtReceived' or
'mvpnIpmsiAdvtReceivedError' or
'mvpnIpmsiAdvtMalformedTunnelType' or
'mvpnIpmsiAdvtMalformedTunnelId' suffered a
discontinuity.
If no such discontinuities have occurred since the
last re-initialization of the local management
subsystem, then this object will have a zero value.
"
::= { mvpnIpmsiAdvtEntry 11 }
-- Table of inter-as I-PMSIs advertised/received -- Table of inter-as I-PMSIs advertised/received
mvpnInterAsIpmsiTable OBJECT-TYPE mvpnInterAsIpmsiAdvtTable OBJECT-TYPE
SYNTAX SEQUENCE OF MvpnInterAsIpmsiEntry SYNTAX SEQUENCE OF MvpnInterAsIpmsiAdvtEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table is for all advertised/received inter-as I-PMSI "This table is for all advertised/received inter-as I-PMSI
advertisements." advertisements."
::= { mvpnStates 2 } ::= { mvpnStates 2 }
mvpnInterAsIpmsiEntry OBJECT-TYPE mvpnInterAsIpmsiAdvtEntry OBJECT-TYPE
SYNTAX MvpnInterAsIpmsiEntry SYNTAX MvpnInterAsIpmsiAdvtEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An entry in this table corresponds to an inter-as I-PMSI "An entry in this table corresponds to an inter-as I-PMSI
advertisement that is advertised/received on this router. advertisement that is advertised/received by this router.
This represents all the ASes in the MVPN, This represents all the ASes in the MVPN,
with the provider tunnel used to send traffic to. with the provider tunnel used to send traffic to.
Implementers need to be aware that there are quite a few
index objects that together can exceed the size allowed
for an Object Identifier (OID). So implementers must make
sure that OIDs of column instances in this table will have
no more than 128 sub-identifiers, otherwise they cannot be
accessed using SNMPv1, SNMPv2c, or SNMPv3.
" "
INDEX { INDEX {
mplsL3VpnVrfName, mplsL3VpnVrfName,
mvpnInterAsIpmsiAfi, mvpnInterAsIpmsiAdvtAfi,
mvpnInterAsIpmsiRD, mvpnInterAsIpmsiAdvtRD,
mvpnInterAsIpmsiSrcAs mvpnInterAsIpmsiAdvtSrcAs
} }
::= { mvpnInterAsIpmsiTable 1 } ::= { mvpnInterAsIpmsiAdvtTable 1 }
MvpnInterAsIpmsiEntry ::= SEQUENCE { MvpnInterAsIpmsiAdvtEntry ::= SEQUENCE {
mvpnInterAsIpmsiAfi INTEGER, mvpnInterAsIpmsiAdvtAfi INTEGER,
mvpnInterAsIpmsiRD MplsL3VpnRouteDistinguisher, mvpnInterAsIpmsiAdvtRD MplsL3VpnRouteDistinguisher,
mvpnInterAsIpmsiSrcAs InetAutonomousSystemNumber, mvpnInterAsIpmsiAdvtSrcAs InetAutonomousSystemNumber,
mvpnInterAsIpmsiAttribute RowPointer mvpnInterAsIpmsiAdvtTunnelAttribute RowPointer,
mvpnInterAsIpmsiAdvtReceived Counter32,
mvpnInterAsIpmsiAdvtReceivedError Counter32,
mvpnInterAsIpmsiAdvtMalformedTunnelType Counter32,
mvpnInterAsIpmsiAdvtMalformedTunnelId Counter32,
mvpnInterAsIpmsiAdvtLastReceivedTime TimeStamp,
mvpnInterAsIpmsiAdvtCounterDiscontinuityTime TimeStamp
} }
mvpnInterAsIpmsiAfi OBJECT-TYPE mvpnInterAsIpmsiAdvtAfi OBJECT-TYPE
SYNTAX INTEGER { SYNTAX INTEGER {
ipv4(1), ipv4(1),
ipv6(2) ipv6(2)
} }
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The address family this I-PMSI is for." "The address family this I-PMSI is for."
::= { mvpnInterAsIpmsiEntry 1 } ::= { mvpnInterAsIpmsiAdvtEntry 1 }
mvpnInterAsIpmsiRD OBJECT-TYPE mvpnInterAsIpmsiAdvtRD OBJECT-TYPE
SYNTAX MplsL3VpnRouteDistinguisher SYNTAX MplsL3VpnRouteDistinguisher
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The Route Distinguisher in this inter-as I-PMSI." "The Route Distinguisher in this inter-as I-PMSI."
::= { mvpnInterAsIpmsiEntry 2 } ::= { mvpnInterAsIpmsiAdvtEntry 2 }
mvpnInterAsIpmsiSrcAs OBJECT-TYPE mvpnInterAsIpmsiAdvtSrcAs OBJECT-TYPE
SYNTAX InetAutonomousSystemNumber SYNTAX InetAutonomousSystemNumber
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The source-as in this inter-as I-PMSI." "The source-as in this inter-as I-PMSI."
::= { mvpnInterAsIpmsiEntry 3 } ::= { mvpnInterAsIpmsiAdvtEntry 3 }
mvpnInterAsIpmsiAttribute OBJECT-TYPE mvpnInterAsIpmsiAdvtTunnelAttribute OBJECT-TYPE
SYNTAX RowPointer SYNTAX RowPointer
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Points to a row in the l2L3VpnMcastPmsiTunnelAttributeTable." "Points to a row in the l2L3VpnMcastPmsiTunnelAttributeTable."
::= { mvpnInterAsIpmsiEntry 4 } ::= { mvpnInterAsIpmsiAdvtEntry 4 }
mvpnInterAsIpmsiAdvtReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Inter-AS I-PMSI advertisements received
by the PE router.
This includes advertisements that were discarded.
Discontinuities in the value of this counter can
occur at re-initialization of the management system,
and at other times as indicated by the value of
mvpnInterAsIpmsiAdvtCounterDiscontinuityTime.
"
::= { mvpnInterAsIpmsiAdvtEntry 5 }
mvpnInterAsIpmsiAdvtReceivedError OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of errors in the Inter-AS I-PMSI
advertisements received by the PE router.
The value of this object is the sum of
the values of mvpnInterAsIpmsiAdvtMalformedTunnelType and
mvpnInterAsIpmsiAdvtMalformedTunnelId.
Discontinuities in the value of this counter can
occur at re-initialization of the management system,
and at other times as indicated by the value of
mvpnInterAsIpmsiAdvtCounterDiscontinuityTime.
"
::= { mvpnInterAsIpmsiAdvtEntry 6 }
mvpnInterAsIpmsiAdvtMalformedTunnelType OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of received Inter-AS I-PMSI advertisements that
contain a PMSI Tunnel attribute whose Tunnel
Type field has an undefined tunnel type.
Discontinuities in the value of this counter can
occur at re-initialization of the management system,
and at other times as indicated by the value of
mvpnInterAsIpmsiAdvtCounterDiscontinuityTime.
"
REFERENCE
"RFC6514 Sec.5"
::= { mvpnInterAsIpmsiAdvtEntry 7 }
mvpnInterAsIpmsiAdvtMalformedTunnelId OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of received Inter-AS I-PMSI advertisements that
contain a PMSI Tunnel attribute whose Tunnel
Identifier field cannot be parsed as a
tunnel identifier of the tunnel types specified in
the Tunnel type field of the attribute.
Discontinuities in the value of this counter can
occur at re-initialization of the management system,
and at other times as indicated by the value of
mvpnInterAsIpmsiAdvtCounterDiscontinuityTime.
"
REFERENCE
"RFC6514 Sec.5"
::= { mvpnInterAsIpmsiAdvtEntry 8 }
mvpnInterAsIpmsiAdvtLastReceivedTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when the last Inter-AS I-PMSI
advertisement was received by the PE router.
"
::= { mvpnInterAsIpmsiAdvtEntry 9 }
mvpnInterAsIpmsiAdvtCounterDiscontinuityTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime on the most recent occasion
at which any one or more of this syslog application's
counters, viz., counters with OID prefix
'mvpnInterAsIpmsiAdvtReceived' or
'mvpnInterAsIpmsiAdvtReceivedError' or
'mvpnInterAsIpmsiAdvtMalformedTunnelType' or
'mvpnInterAsIpmsiAdvtMalformedTunnelId' suffered a
discontinuity.
If no such discontinuities have occurred since the
last re-initialization of the local management
subsystem, then this object will have a zero value.
"
::= { mvpnInterAsIpmsiAdvtEntry 10 }
-- Table of S-PMSIs advertised/received -- Table of S-PMSIs advertised/received
mvpnSpmsiTable OBJECT-TYPE mvpnSpmsiAdvtTable OBJECT-TYPE
SYNTAX SEQUENCE OF MvpnSpmsiEntry SYNTAX SEQUENCE OF MvpnSpmsiAdvtEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table has information about the S-PMSIs sent/received "This table has information about the S-PMSIs sent/received
by a PE. by a PE.
" "
::= { mvpnStates 3 } ::= { mvpnStates 3 }
mvpnSpmsiEntry OBJECT-TYPE mvpnSpmsiAdvtEntry OBJECT-TYPE
SYNTAX MvpnSpmsiEntry SYNTAX MvpnSpmsiAdvtEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An entry in this table is created or updated for each S-PMSI "An entry in this table is created or updated for each S-PMSI
advertised/received in a particular MVRF. advertised/received in a particular MVRF.
Implementers need to be aware that there are quite a few
index objects that together can exceed the size allowed
for an Object Identifier (OID). So implementers must make
sure that OIDs of column instances in this table will have
no more than 128 sub-identifiers, otherwise they cannot be
accessed using SNMPv1, SNMPv2c, or SNMPv3.
" "
INDEX { INDEX {
mplsL3VpnVrfName, mplsL3VpnVrfName,
mvpnSpmsiCmcastAddrType, mvpnSpmsiAdvtCmcastAddrType,
mvpnSpmsiCmcastGroupAddr, mvpnSpmsiAdvtCmcastGroupAddr,
mvpnSpmsiCmcastGroupPrefixLen, mvpnSpmsiAdvtCmcastGroupPrefixLen,
mvpnSpmsiCmcastSourceAddr, mvpnSpmsiAdvtCmcastSourceAddr,
mvpnSpmsiCmcastSourcePrefixLen, mvpnSpmsiAdvtCmcastSourcePrefixLen,
mvpnSpmsiOrigAddrType, mvpnSpmsiAdvtOrigAddrType,
mvpnSpmsiOrigAddr mvpnSpmsiAdvtOrigAddr
} }
::= { mvpnSpmsiTable 1 } ::= { mvpnSpmsiAdvtTable 1 }
MvpnSpmsiEntry ::= SEQUENCE { MvpnSpmsiAdvtEntry ::= SEQUENCE {
mvpnSpmsiCmcastAddrType InetAddressType, mvpnSpmsiAdvtCmcastAddrType InetAddressType,
mvpnSpmsiCmcastGroupAddr InetAddress, mvpnSpmsiAdvtCmcastGroupAddr InetAddress,
mvpnSpmsiCmcastGroupPrefixLen InetAddressPrefixLength, mvpnSpmsiAdvtCmcastGroupPrefixLen InetAddressPrefixLength,
mvpnSpmsiCmcastSourceAddr InetAddress, mvpnSpmsiAdvtCmcastSourceAddr InetAddress,
mvpnSpmsiCmcastSourcePrefixLen InetAddressPrefixLength, mvpnSpmsiAdvtCmcastSourcePrefixLen InetAddressPrefixLength,
mvpnSpmsiOrigAddrType InetAddressType, mvpnSpmsiAdvtOrigAddrType InetAddressType,
mvpnSpmsiOrigAddr InetAddress, mvpnSpmsiAdvtOrigAddr InetAddress,
mvpnSpmsiTunnelAttribute RowPointer, mvpnSpmsiAdvtTunnelAttribute RowPointer,
mvpnSpmsiUpTime TimeInterval, mvpnSpmsiAdvtExpTime TimeInterval,
mvpnSpmsiExpTime TimeInterval, mvpnSpmsiAdvtRefCnt Unsigned32,
mvpnSpmsiRefCnt Unsigned32 mvpnSpmsiAdvtReceived Counter32,
mvpnSpmsiAdvtReceivedError Counter32,
mvpnSpmsiAdvtMalformedTunnelType Counter32,
mvpnSpmsiAdvtMalformedTunnelId Counter32,
mvpnSpmsiAdvtLastReceivedTime TimeStamp,
mvpnSpmsiAdvtCounterDiscontinuityTime TimeStamp
} }
mvpnSpmsiCmcastAddrType OBJECT-TYPE mvpnSpmsiAdvtCmcastAddrType OBJECT-TYPE
SYNTAX InetAddressType SYNTAX InetAddressType
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The Internet address type of mvpnSpmsiCmcastGroup/Source." "The Internet address type of mvpnSpmsiAdvtCmcastGroup/Source."
::= { mvpnSpmsiEntry 1 } ::= { mvpnSpmsiAdvtEntry 1 }
mvpnSpmsiCmcastGroupAddr OBJECT-TYPE mvpnSpmsiAdvtCmcastGroupAddr OBJECT-TYPE
SYNTAX InetAddress SYNTAX InetAddress
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"S-PMSI C-multicast group address. "S-PMSI C-multicast group address.
If it is 0 (or ::0), this is a wildcard group, If it is 0 (or ::0), this is a wildcard group,
and mvpnSpmsiCmcastGroupPrefixLen must be 32 (or 128). and mvpnSpmsiAdvtCmcastGroupPrefixLen must be 32 (or 128).
" "
::= { mvpnSpmsiEntry 2 } ::= { mvpnSpmsiAdvtEntry 2 }
mvpnSpmsiCmcastGroupPrefixLen OBJECT-TYPE mvpnSpmsiAdvtCmcastGroupPrefixLen OBJECT-TYPE
SYNTAX InetAddressPrefixLength SYNTAX InetAddressPrefixLength
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"S-PMSI C-multicast group address prefix length." "S-PMSI C-multicast group address prefix length."
::= { mvpnSpmsiEntry 3 } ::= { mvpnSpmsiAdvtEntry 3 }
mvpnSpmsiCmcastSourceAddr OBJECT-TYPE mvpnSpmsiAdvtCmcastSourceAddr OBJECT-TYPE
SYNTAX InetAddress SYNTAX InetAddress
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"S-PMSI C-multicast source address "S-PMSI C-multicast source address
If it is 0 (or ::0), this is a wildcard source, If it is 0 (or ::0), this is a wildcard source,
and mvpnSpmsiCmcastSourcePrefixLen must be 32 (or 128). and mvpnSpmsiAdvtCmcastSourcePrefixLen must be 32 (or 128).
" "
::= { mvpnSpmsiEntry 4 } ::= { mvpnSpmsiAdvtEntry 4 }
mvpnSpmsiCmcastSourcePrefixLen OBJECT-TYPE mvpnSpmsiAdvtCmcastSourcePrefixLen OBJECT-TYPE
SYNTAX InetAddressPrefixLength SYNTAX InetAddressPrefixLength
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"S-PMSI C-multicast source address prefix length." "S-PMSI C-multicast source address prefix length."
::= { mvpnSpmsiEntry 5 } ::= { mvpnSpmsiAdvtEntry 5 }
mvpnSpmsiOrigAddrType OBJECT-TYPE mvpnSpmsiAdvtOrigAddrType OBJECT-TYPE
SYNTAX InetAddressType SYNTAX InetAddressType
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The Internet address type of mvpnSpmsiOrigAddr." "The Internet address type of mvpnSpmsiAdvtOrigAddr."
::= { mvpnSpmsiEntry 6 } ::= { mvpnSpmsiAdvtEntry 6 }
mvpnSpmsiOrigAddr OBJECT-TYPE mvpnSpmsiAdvtOrigAddr OBJECT-TYPE
SYNTAX InetAddress SYNTAX InetAddress
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The BGP address of the PE that originated the S-PMSI." "The BGP address of the PE that originated the S-PMSI."
::= { mvpnSpmsiEntry 7 } ::= { mvpnSpmsiAdvtEntry 7 }
mvpnSpmsiTunnelAttribute OBJECT-TYPE mvpnSpmsiAdvtTunnelAttribute OBJECT-TYPE
SYNTAX RowPointer SYNTAX RowPointer
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"A row pointer to the l2L3VpnMcastPmsiTunnelAttributeTable" "A row pointer to the l2L3VpnMcastPmsiTunnelAttributeTable"
::= { mvpnSpmsiEntry 8 } ::= { mvpnSpmsiAdvtEntry 8 }
mvpnSpmsiUpTime OBJECT-TYPE
SYNTAX TimeInterval
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time since this S-PMSI
was first advertised/received by the PE.
"
::= { mvpnSpmsiEntry 9 }
mvpnSpmsiExpTime OBJECT-TYPE mvpnSpmsiAdvtExpTime OBJECT-TYPE
SYNTAX TimeInterval SYNTAX TimeInterval
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"For UDP-based S-PMSI signaling for PIM-MVPN, "For UDP-based S-PMSI signaling for PIM-MVPN,
the amount of time remaining before this the amount of time remaining before this
received S-PMSI Join Message expires, received S-PMSI Join Message expires,
or the next S-PMSI Join Message refresh is to be or the next S-PMSI Join Message refresh is to be
advertised again from the PE. advertised again from the PE.
Otherwise, it is 0. Otherwise, it is 0.
" "
::= { mvpnSpmsiEntry 10 } ::= { mvpnSpmsiAdvtEntry 9 }
mvpnSpmsiRefCnt OBJECT-TYPE mvpnSpmsiAdvtRefCnt OBJECT-TYPE
SYNTAX Unsigned32 SYNTAX Unsigned32
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The number of c-multicast routes that are mapped to "The number of c-multicast routes that are mapped to
this S-PMSI. this S-PMSI.
" "
::= { mvpnSpmsiEntry 11 } ::= { mvpnSpmsiAdvtEntry 10 }
mvpnSpmsiAdvtReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of S-PMSI advertisements received by the PE router.
This includes advertisements that were discarded.
Discontinuities in the value of this counter can
occur at re-initialization of the management system,
and at other times as indicated by the value of
mvpnIpmsiAdvtCounterDiscontinuityTime.
"
::= { mvpnSpmsiAdvtEntry 11 }
mvpnSpmsiAdvtReceivedError OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of errors in the S-PMSI advertisements
received by the PE router.
The value of this object is the sum of
the values of mvpnSpmsiAdvtMalformedTunnelType and
mvpnSpmsiAdvtMalformedTunnelId.
Discontinuities in the value of this counter can
occur at re-initialization of the management system,
and at other times as indicated by the value of
mvpnSpmsiAdvtCounterDiscontinuityTime.
"
::= { mvpnSpmsiAdvtEntry 12 }
mvpnSpmsiAdvtMalformedTunnelType OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of received S-PMSI advertisements that
contain a PMSI Tunnel attribute whose Tunnel
Type field has an undefined tunnel type.
Discontinuities in the value of this counter can
occur at re-initialization of the management system,
and at other times as indicated by the value of
mvpnSpmsiAdvtCounterDiscontinuityTime.
"
REFERENCE
"RFC6514 Sec.5"
::= { mvpnSpmsiAdvtEntry 13 }
mvpnSpmsiAdvtMalformedTunnelId OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of received S-PMSI advertisements that
contain a PMSI Tunnel attribute whose Tunnel
Identifier field cannot be parsed as a
tunnel identifier of the tunnel types specified in
the Tunnel type field of the attribute.
Discontinuities in the value of this counter can
occur at re-initialization of the management system,
and at other times as indicated by the value of
mvpnSpmsiAdvtCounterDiscontinuityTime.
"
REFERENCE
"RFC6514 Sec.5"
::= { mvpnSpmsiAdvtEntry 14 }
mvpnSpmsiAdvtLastReceivedTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when the last S-PMSI
advertisement was received by the PE router.
"
::= { mvpnSpmsiAdvtEntry 15 }
mvpnSpmsiAdvtCounterDiscontinuityTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime on the most recent occasion
at which any one or more of this syslog application's
counters, viz., counters with OID prefix
'mvpnSpmsiAdvtReceived' or
'mvpnSpmsiAdvtReceivedError' or
'mvpnSpmsiAdvtMalformedTunnelType' or
'mvpnSpmsiAdvtMalformedTunnelId' suffered a
discontinuity.
If no such discontinuities have occurred since the
last re-initialization of the local management
subsystem, then this object will have a zero value.
"
::= { mvpnSpmsiAdvtEntry 16 }
-- Table of multicast routes in an MVPN -- Table of multicast routes in an MVPN
mvpnMrouteTable OBJECT-TYPE mvpnMrouteTable OBJECT-TYPE
SYNTAX SEQUENCE OF MvpnMrouteEntry SYNTAX SEQUENCE OF MvpnMrouteEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table augments ipMcastRouteTable, to provide some MVPN "This table contains multicast routing information
specific information. in MVRFs present in the PE.
" "
::= { mvpnStates 4 } ::= { mvpnStates 4 }
mvpnMrouteEntry OBJECT-TYPE mvpnMrouteEntry OBJECT-TYPE
SYNTAX MvpnMrouteEntry SYNTAX MvpnMrouteEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The mvpnMrouteEntry matches and augments an ipMcastRouteEntry, "This entry corresponds to each of multicast routing
with MVPN specific information, such as PMSI used. information components for IP datagrams
from a particular source and addressed to a particular
IP multicast group address.
OIDs are limited to 128 sub-identifiers, but this limit
is not enforced by the syntax of this entry. In practice,
this does not present a problem, because IP address types
allowed by conformance statements do not exceed this limit.
" "
AUGMENTS { ipMcastRouteEntry } INDEX {
::= { mvpnMrouteTable 1 } mplsL3VpnVrfName,
mvpnMrouteCmcastGroupAddrType,
mvpnMrouteCmcastGroupAddr,
mvpnMrouteCmcastGroupPrefixLength,
mvpnMrouteCmcastSourceAddrType,
mvpnMrouteCmcastSourceAddr,
mvpnMrouteCmcastSourcePrefixLength
}
::= { mvpnMrouteTable 1 }
MvpnMrouteEntry ::= SEQUENCE { MvpnMrouteEntry ::= SEQUENCE {
mvpnMrouteCmcastGroupAddrType InetAddressType,
mvpnMrouteCmcastGroupAddr InetAddress,
mvpnMrouteCmcastGroupPrefixLength InetAddressPrefixLength,
mvpnMrouteCmcastSourceAddrType InetAddressType,
mvpnMrouteCmcastSourceAddr InetAddress,
mvpnMrouteCmcastSourcePrefixLength InetAddressPrefixLength,
mvpnMrouteUpstreamNeighborAddrType InetAddressType,
mvpnMrouteUpstreamNeighborAddr InetAddress,
mvpnMrouteInIfIndex InterfaceIndexOrZero,
mvpnMrouteTimeStamp TimeStamp,
mvpnMrouteExpiryTime TimeTicks,
mvpnMrouteProtocol IANAipMRouteProtocol,
mvpnMrouteRtProtocol IANAipRouteProtocol,
mvpnMrouteRtAddrType InetAddressType,
mvpnMrouteRtAddr InetAddress,
mvpnMrouteRtPrefixLength InetAddressPrefixLength,
mvpnMrouteRtType INTEGER,
mvpnMrouteOctets Counter64,
mvpnMroutePkts Counter64,
mvpnMrouteTtlDropOctets Counter64,
mvpnMrouteTtlDropPackets Counter64,
mvpnMrouteDifferentInIfOctets Counter64,
mvpnMrouteDifferentInIfPackets Counter64,
mvpnMrouteBps CounterBasedGauge64,
mvpnMroutePmsiPointer RowPointer, mvpnMroutePmsiPointer RowPointer,
mvpnMrouteNumberOfLocalReplication Unsigned32, mvpnMrouteNumberOfLocalReplication Unsigned32,
mvpnMrouteNumberOfRemoteReplication Unsigned32 mvpnMrouteNumberOfRemoteReplication Unsigned32
} }
mvpnMrouteCmcastGroupAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A value indicating the address family of the address
contained in mvpnMrouteGroupAddr. Legal values correspond to
the subset of address families for which multicast
forwarding is supported."
::= { mvpnMrouteEntry 1 }
mvpnMrouteCmcastGroupAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The IP multicast group address which, when combined with
the corresponding value specified in
mvpnMrouteGroupPrefixLength, identifies the groups for
which this entry contains multicast routing information.
This address object is only significant up to
mvpnMrouteGroupPrefixLength bits. The remaining address
bits are set to zero. This is especially important for this
index field, which is part of the index of this entry. Any
non-zero bits would signify an entirely different entry.
For addresses of type ipv4z or ipv6z, the appended zone
index is significant even though it lies beyond the prefix
length. The use of these address types indicate that this
forwarding state applies only within the given zone. Zone
index zero is not valid in this table."
::= { mvpnMrouteEntry 2 }
mvpnMrouteCmcastGroupPrefixLength OBJECT-TYPE
SYNTAX InetAddressPrefixLength
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The length in bits of the mask which, when combined with
the corresponding value of mvpnMrouteGroupAddr, identifies the
groups for which this entry contains multicast routing
information.
The InetAddressType is given by
mvpnMrouteGroupAddrType. For values 'ipv4' and
'ipv4z', this object must be in the range 4..32. For values
'ipv6' and 'ipv6z', this object must be in the range
8..128.
"
::= { mvpnMrouteEntry 3 }
mvpnMrouteCmcastSourceAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A value indicating the address family of the address
contained in mvpnMrouteSourceAddr.
A value of unknown(0) indicates a non-source-specific entry,
corresponding to all sources in the group. Otherwise, the
value MUST be the same as the value of
mvpnMrouteGroupAddrType.
"
::= { mvpnMrouteEntry 4 }
mvpnMrouteCmcastSourceAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The network address which, when combined with the
corresponding value of mvpnMrouteSourcePrefixLength,
identifies the sources for which this entry contains
multicast routing information.
This address object is only significant up to
mvpnMrouteSourcePrefixLength bits. The remaining address
bits are set to zero. This is especially important for this
index field, which is part of the index of this entry. Any
non-zero bits would signify an entirely different entry.
For addresses of type ipv4z or ipv6z, the appended zone
index is significant even though it lies beyond the prefix
length. The use of these address types indicate that this
source address applies only within the given zone. Zone
index zero is not valid in this table.
"
::= { mvpnMrouteEntry 5 }
mvpnMrouteCmcastSourcePrefixLength OBJECT-TYPE
SYNTAX InetAddressPrefixLength
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The length in bits of the mask which, when combined with
the corresponding value of mvpnMrouteSource, identifies
the sources for which this entry contains multicast routing
information.
The InetAddressType is given by
mvpnMrouteSourceAddrType. For the value 'unknown',
this object must be zero. For values 'ipv4' and 'ipv4z',
this object must be in the range 4..32. For values 'ipv6'
and 'ipv6z', this object must be in the range 8..128."
::= { mvpnMrouteEntry 6 }
mvpnMrouteUpstreamNeighborAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A value indicating the address family of the address
contained in mvpnMrouteUpstreamNeighborAddr.
An address type of unknown(0) indicates that the upstream
neighbor is unknown, for example in BIDIR-PIM."
REFERENCE "RFC 5015"
::= { mvpnMrouteEntry 7 }
mvpnMrouteUpstreamNeighborAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The address of the upstream neighbor (for example, RPF
neighbor) from which IP datagrams from these sources to
this multicast address are received.
"
::= { mvpnMrouteEntry 8 }
mvpnMrouteInIfIndex OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ifIndex for the interface on which IP
datagrams sent by these sources to this multicast address
are received. A value of 0 indicates that datagrams are not
subject to an incoming interface check, but may be accepted
on multiple interfaces (for example, in BIDIR-PIM).
"
REFERENCE
"RFC 5015"
::= { mvpnMrouteEntry 9 }
mvpnMrouteTimeStamp OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at which the multicast routing
information represented by this entry was learned by the
router.
If this information was present at the most recent re-
initialization of the local management subsystem, then this
object contains a zero value.
"
::= { mvpnMrouteEntry 10 }
mvpnMrouteExpiryTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimum amount of time remaining before this entry will
be aged out. The value 0 indicates that the entry is not
subject to aging. If mvpnMrouteNextHopState is pruned(1),
this object represents the remaining time until the prune
expires. If this timer expires, state reverts to
forwarding(2). Otherwise, this object represents the time
until this entry is removed from the table.
"
::= { mvpnMrouteEntry 11 }
mvpnMrouteProtocol OBJECT-TYPE
SYNTAX IANAipMRouteProtocol
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The multicast routing protocol via which this multicast
forwarding entry was learned.
"
::= { mvpnMrouteEntry 12 }
mvpnMrouteRtProtocol OBJECT-TYPE
SYNTAX IANAipRouteProtocol
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The routing mechanism via which the route used to find the
upstream or parent interface for this multicast forwarding
entry was learned.
"
::= { mvpnMrouteEntry 13 }
mvpnMrouteRtAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A value indicating the address family of the address
contained in mvpnMrouteRtAddr.
"
::= { mvpnMrouteEntry 14 }
mvpnMrouteRtAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The address portion of the route used to find the upstream
or parent interface for this multicast forwarding entry.
This address object is only significant up to
mvpnMrouteRtPrefixLength bits. The remaining address bits
are set to zero.
For addresses of type ipv4z or ipv6z, the appended zone
index is significant even though it lies beyond the prefix
length. The use of these address types indicate that this
forwarding state applies only within the given zone. Zone
index zero is not valid in this table.
"
::= { mvpnMrouteEntry 15 }
mvpnMrouteRtPrefixLength OBJECT-TYPE
SYNTAX InetAddressPrefixLength
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The length in bits of the mask associated with the route
used to find the upstream or parent interface for this
multicast forwarding entry.
The InetAddressType is given by mvpnMrouteRtAddressType.
For values 'ipv4' and 'ipv4z', this object must be in the
range 4..32. For values 'ipv6' and 'ipv6z', this object
must be in the range 8..128.
"
::= { mvpnMrouteEntry 16 }
mvpnMrouteRtType OBJECT-TYPE
SYNTAX INTEGER {
unicast (1), -- Unicast route used in multicast RIB
multicast (2) -- Multicast route
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The reason the given route was placed in the (logical)
multicast Routing Information Base (RIB). A value of
unicast means that the route would normally be placed only
in the unicast RIB, but was placed in the multicast RIB
due (instead or in addition) to local configuration, such as
when running PIM over RIP. A value of multicast means that
the route was explicitly added to the multicast RIB by the
routing protocol, such as the Distance Vector Multicast
Routing Protocol (DVMRP) or Multiprotocol BGP.
"
::= { mvpnMrouteEntry 17 }
mvpnMrouteOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets contained in IP datagrams that were
received from these sources and addressed to this multicast
group address, and which were forwarded by this router.
Discontinuities in this monotonically increasing value
occur at re-initialization of the management system.
Discontinuities can also occur as a result of routes being
removed and replaced, which can be detected by observing
the value of mvpnMrouteTimeStamp.
"
::= { mvpnMrouteEntry 18 }
mvpnMroutePkts OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets routed using this multicast route
entry.
Discontinuities in this monotonically increasing value
occur at re-initialization of the management system.
Discontinuities can also occur as a result of routes being
removed and replaced, which can be detected by observing
the value of mvpnMrouteTimeStamp.
"
::= { mvpnMrouteEntry 19 }
mvpnMrouteTtlDropOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets contained in IP datagrams that this
router has received from these sources and addressed to this
multicast group address, which were dropped because the TTL
(IPv4) or Hop Limit (IPv6) was decremented to zero, or to a
value less than ipMcastInterfaceTtl for all next hops.
Discontinuities in this monotonically increasing value
occur at re-initialization of the management system.
Discontinuities can also occur as a result of routes being
removed and replaced, which can be detected by observing
the value of mvpnMrouteTimeStamp.
"
::= { mvpnMrouteEntry 20 }
mvpnMrouteTtlDropPackets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets that this router has received from
these sources and addressed to this multicast group address,
which were dropped because the TTL (IPv4) or Hop Limit
(IPv6) was decremented to zero, or to a value less than
ipMcastInterfaceTtl for all next hops.
Discontinuities in this monotonically increasing value
occur at re-initialization of the management system.
Discontinuities can also occur as a result of routes being
removed and replaced, which can be detected by observing
the value of mvpnMrouteTimeStamp.
"
::= { mvpnMrouteEntry 21 }
mvpnMrouteDifferentInIfOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets contained in IP datagrams that this
router has received from these sources and addressed to this
multicast group address, which were dropped because they
were received on an unexpected interface.
For RPF checking protocols (such as PIM-SM), these packets
arrived on interfaces other than mvpnMrouteInIfIndex, and
were dropped because of this failed RPF check. (RPF paths
are 'Reverse Path Forwarding' paths; the unicast routes to
the expected origin of multicast data flows).
Other protocols may drop packets on an incoming interface
check for different reasons (for example, BIDIR-PIM performs
a DF check on receipt of packets). All packets dropped as a
result of an incoming interface check are counted here.
If this counter increases rapidly, this indicates a problem.
A significant quantity of multicast data is arriving at this
router on unexpected interfaces, and is not being forwarded.
For guidance, if the rate of increase of this counter
exceeds 1% of the rate of increase of mvpnMrouteOctets,
then there are multicast routing problems that require
investigation.
Discontinuities in this monotonically increasing value
occur at re-initialization of the management system.
Discontinuities can also occur as a result of routes being
removed and replaced, which can be detected by observing
the value of mvpnMrouteTimeStamp.
"
REFERENCE
"RFC 4601
RFC 5015
"
::= { mvpnMrouteEntry 22 }
mvpnMrouteDifferentInIfPackets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets which this router has received from
these sources and addressed to this multicast group address,
which were dropped because they were received on an
unexpected interface.
For RPF checking protocols (such as PIM-SM), these packets
arrived on interfaces other than mvpnMrouteInIfIndex, and
were dropped because of this failed RPF check. (RPF paths
are 'Reverse Path Forwarding' path; the unicast routes to
the expected origin of multicast data flows).
Other protocols may drop packets on an incoming interface
check for different reasons (for example, BIDIR-PIM performs
a DF check on receipt of packets). All packets dropped as a
result of an incoming interface check are counted here.
If this counter increases rapidly, this indicates a problem.
A significant quantity of multicast data is arriving at this
router on unexpected interfaces, and is not being forwarded.
For guidance, if the rate of increase of this counter
exceeds 1% of the rate of increase of mvpnMroutePkts, then
there are multicast routing problems that require
investigation.
Discontinuities in this monotonically increasing value
occur at re-initialization of the management system.
Discontinuities can also occur as a result of routes being
removed and replaced, which can be detected by observing
the value of mvpnMrouteTimeStamp.
"
REFERENCE
"RFC 4601
RFC 5015
"
::= { mvpnMrouteEntry 23 }
mvpnMrouteBps OBJECT-TYPE
SYNTAX CounterBasedGauge64
UNITS "bits per second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Bits per second forwarded by this router using this
multicast routing entry.
This value is a sample; it is the number of bits forwarded
during the last whole 1 second sampling period. The value
during the current 1 second sampling period is not made
available until the period is completed.
The quantity being sampled is the same as that measured by
mvpnMrouteOctets. The units and the sampling method are
different.
"
::= { mvpnMrouteEntry 24 }
mvpnMroutePmsiPointer OBJECT-TYPE mvpnMroutePmsiPointer OBJECT-TYPE
SYNTAX RowPointer SYNTAX RowPointer
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The I-PMSI or S-PMSI this C-multicast route is using. "The I-PMSI or S-PMSI this C-multicast route is using.
This is important because an implementation may not have an This is important because an implementation may not have an
interface corresponding to a provider tunnel, interface corresponding to a provider tunnel,
that can be used in ipMcastRouteNextHopEntry. that can be used in mvpnMrouteNextHopEntry.
" "
::= { mvpnMrouteEntry 1 } ::= { mvpnMrouteEntry 25 }
mvpnMrouteNumberOfLocalReplication OBJECT-TYPE mvpnMrouteNumberOfLocalReplication OBJECT-TYPE
SYNTAX Unsigned32 SYNTAX Unsigned32
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Number of replications for local receivers. "Number of replications for local receivers.
For example, if an ingress PE needs to send traffic out of For example, if an ingress PE needs to send traffic out of
N PE-CE interfaces, then mvpnMrouteNumberOfLocalReplication N PE-CE interfaces, then mvpnMrouteNumberOfLocalReplication
is N. is N.
" "
::= { mvpnMrouteEntry 2 } ::= { mvpnMrouteEntry 26 }
mvpnMrouteNumberOfRemoteReplication OBJECT-TYPE mvpnMrouteNumberOfRemoteReplication OBJECT-TYPE
SYNTAX Unsigned32 SYNTAX Unsigned32
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Number of local replications for remote PEs. For example, "Number of local replications for remote PEs. For example,
if the number of remote PEs that need to receive traffic is N, if the number of remote PEs that need to receive traffic is N,
then mvpnMrouteNumberOfRemoteReplication is N in case of then mvpnMrouteNumberOfRemoteReplication is N in case of
Ingress Replication, but may be less than N in case of RSVP-TE Ingress Replication, but may be less than N in case of RSVP-TE
or mLDP P2MP tunnels, depending on the actual number of or mLDP P2MP tunnels, depending on the actual number of
replications the PE needs do. replications the PE needs do.
" "
::= { mvpnMrouteEntry 3 }
::= { mvpnMrouteEntry 27 }
mvpnMrouteNextHopTable OBJECT-TYPE
SYNTAX SEQUENCE OF MvpnMrouteNextHopEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The (conceptual) table containing information on the
next-hops on outgoing interfaces for routing IP multicast
datagrams. Each entry is one of a list of next-hops on
outgoing interfaces for particular sources sending to a
particular multicast group address."
::= { mvpnStates 5 }
mvpnMrouteNextHopEntry OBJECT-TYPE
SYNTAX MvpnMrouteNextHopEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the list of next-hops on
outgoing interfaces to which IP multicast datagrams from
particular sources to an IP multicast group address are
routed.
OIDs are limited to 128 sub-identifiers, but this limit
is not enforced by the syntax of this entry. In practice,
this does not present a problem, because IP address types
allowed by conformance statements do not exceed this limit.
"
INDEX {
mplsL3VpnVrfName,
mvpnMrouteNextHopGroupAddrType,
mvpnMrouteNextHopGroupAddr,
mvpnMrouteNextHopGroupPrefixLength,
mvpnMrouteNextHopSourceAddrType,
mvpnMrouteNextHopSourceAddr,
mvpnMrouteNextHopSourcePrefixLength,
mvpnMrouteNextHopIfIndex,
mvpnMrouteNextHopAddrType,
mvpnMrouteNextHopAddr
}
::= { mvpnMrouteNextHopTable 1 }
MvpnMrouteNextHopEntry ::= SEQUENCE {
mvpnMrouteNextHopGroupAddrType InetAddressType,
mvpnMrouteNextHopGroupAddr InetAddress,
mvpnMrouteNextHopGroupPrefixLength InetAddressPrefixLength,
mvpnMrouteNextHopSourceAddrType InetAddressType,
mvpnMrouteNextHopSourceAddr InetAddress,
mvpnMrouteNextHopSourcePrefixLength InetAddressPrefixLength,
mvpnMrouteNextHopIfIndex InterfaceIndex,
mvpnMrouteNextHopAddrType InetAddressType,
mvpnMrouteNextHopAddr InetAddress,
mvpnMrouteNextHopState INTEGER,
mvpnMrouteNextHopTimeStamp TimeStamp,
mvpnMrouteNextHopExpiryTime TimeTicks,
mvpnMrouteNextHopClosestMemberHops Unsigned32,
mvpnMrouteNextHopProtocol IANAipMRouteProtocol,
mvpnMrouteNextHopOctets Counter64,
mvpnMrouteNextHopPkts Counter64
}
mvpnMrouteNextHopGroupAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A value indicating the address family of the address
contained in mvpnMrouteNextHopGroupAddr. Legal values
correspond to the subset of address families for which
multicast forwarding is supported.
"
::= { mvpnMrouteNextHopEntry 1 }
mvpnMrouteNextHopGroupAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The IP multicast group address which, when combined with
the corresponding value specified in
mvpnMrouteNextHopGroupPrefixLength, identifies the groups
for which this entry contains multicast forwarding
information.
This address object is only significant up to
mvpnMrouteNextHopGroupPrefixLength bits. The remaining
address bits are set to zero. This is especially important
for this index field, which is part of the index of this
entry. Any non-zero bits would signify an entirely
different entry.
For addresses of type ipv4z or ipv6z, the appended zone
index is significant even though it lies beyond the prefix
length. The use of these address types indicate that this
forwarding state applies only within the given zone. Zone
index zero is not valid in this table.
"
::= { mvpnMrouteNextHopEntry 2 }
mvpnMrouteNextHopGroupPrefixLength OBJECT-TYPE
SYNTAX InetAddressPrefixLength
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The length in bits of the mask which, when combined with
the corresponding value of mvpnMrouteGroup, identifies the
groups for which this entry contains multicast routing
information.
The InetAddressType is given by
mvpnMrouteNextHopGroupAddressType. For values 'ipv4' and
'ipv4z', this object must be in the range 4..32. For values
'ipv6' and 'ipv6z', this object must be in the range
8..128.
"
::= { mvpnMrouteNextHopEntry 3 }
mvpnMrouteNextHopSourceAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A value indicating the address family of the address
contained in mvpnMrouteNextHopSourceAddr.
A value of unknown(0) indicates a non-source-specific entry,
corresponding to all sources in the group. Otherwise, the
value MUST be the same as the value of
mvpnMrouteNextHopGroupAddrType."
::= { mvpnMrouteNextHopEntry 4 }
mvpnMrouteNextHopSourceAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The network address which, when combined with the
corresponding value of the mask specified in
mvpnMrouteNextHopSourcePrefixLength, identifies the
sources for which this entry specifies a next-hop on an
outgoing interface.
This address object is only significant up to
mvpnMrouteNextHopSourcePrefixLength bits. The remaining
address bits are set to zero. This is especially important
for this index field, which is part of the index of this
entry. Any non-zero bits would signify an entirely
different entry.
For addresses of type ipv4z or ipv6z, the appended zone
index is significant even though it lies beyond the prefix
length. The use of these address types indicate that this
source address applies only within the given zone. Zone
index zero is not valid in this table.
"
::= { mvpnMrouteNextHopEntry 5 }
mvpnMrouteNextHopSourcePrefixLength OBJECT-TYPE
SYNTAX InetAddressPrefixLength
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The length in bits of the mask which, when combined with
the corresponding value specified in
mvpnMrouteNextHopSource, identifies the sources for which
this entry specifies a next-hop on an outgoing interface.
The InetAddressType is given by
mvpnMrouteNextHopSourceAddressType. For the value
'unknown', this object must be zero. For values 'ipv4' and
'ipv4z', this object must be in the range 4..32. For values
'ipv6' and 'ipv6z', this object must be in the range
8..128.
"
::= { mvpnMrouteNextHopEntry 6 }
mvpnMrouteNextHopIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ifIndex value of the interface for the outgoing
interface for this next-hop.
"
::= { mvpnMrouteNextHopEntry 7 }
mvpnMrouteNextHopAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A value indicating the address family of the address
contained in mvpnMrouteNextHopAddr.
"
::= { mvpnMrouteNextHopEntry 8 }
mvpnMrouteNextHopAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The address of the next-hop specific to this entry. For
most interfaces, this is identical to
mvpnMrouteNextHopGroup. Non-Broadcast Multi-Access
(NBMA) interfaces, however, may
have multiple next-hop addresses out a single outgoing
interface.
"
::= { mvpnMrouteNextHopEntry 9 }
mvpnMrouteNextHopState OBJECT-TYPE
SYNTAX INTEGER { pruned(1), forwarding(2) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An indication of whether the outgoing interface and next-
hop represented by this entry is currently being used to
forward IP datagrams. The value 'forwarding' indicates it
is currently being used; the value 'pruned' indicates it is
not.
"
::= { mvpnMrouteNextHopEntry 10 }
mvpnMrouteNextHopTimeStamp OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at which the multicast routing
information represented by this entry was learned by the
router.
If this information was present at the most recent re-
initialization of the local management subsystem, then this
object contains a zero value.
"
::= { mvpnMrouteNextHopEntry 11 }
mvpnMrouteNextHopExpiryTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimum amount of time remaining before this entry will
be aged out. If mvpnMrouteNextHopState is pruned(1), the
remaining time until the prune expires and the state reverts
to forwarding(2). Otherwise, the remaining time until this
entry is removed from the table. The time remaining may be
copied from mvpnMrouteExpiryTime if the protocol in use
for this entry does not specify next-hop timers. The value
0 indicates that the entry is not subject to aging.
"
::= { mvpnMrouteNextHopEntry 12 }
mvpnMrouteNextHopClosestMemberHops OBJECT-TYPE
SYNTAX Unsigned32 (0..256)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimum number of hops between this router and any
member of this IP multicast group reached via this next-hop
on this outgoing interface. Any IP multicast datagrams for
the group that have a TTL (IPv4) or Hop Count (IPv6) less
than this number of hops will not be forwarded to this
next-hop.
A value of 0 means all multicast datagrams are forwarded out
the interface. A value of 256 means that no multicast
datagrams are forwarded out the interface.
This is an optimization applied by multicast routing
protocols that explicitly track hop counts to downstream
listeners. Multicast protocols that are not aware of hop
counts to downstream listeners set this object to 0.
"
::= { mvpnMrouteNextHopEntry 13 }
mvpnMrouteNextHopProtocol OBJECT-TYPE
SYNTAX IANAipMRouteProtocol
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The routing mechanism via which this next-hop was learned."
::= { mvpnMrouteNextHopEntry 14 }
mvpnMrouteNextHopOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets of multicast packets that have been
forwarded using this route.
Discontinuities in this monotonically increasing value
occur at re-initialization of the management system.
Discontinuities can also occur as a result of routes being
removed and replaced, which can be detected by observing
the value of mvpnMrouteNextHopTimeStamp."
::= { mvpnMrouteNextHopEntry 15 }
mvpnMrouteNextHopPkts OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets which have been forwarded using this
route.
Discontinuities in this monotonically increasing value
occur at re-initialization of the management system.
Discontinuities can also occur as a result of routes being
removed and replaced, which can be detected by observing
the value of ipMcastRouteNextHopTimeStamp."
::= { mvpnMrouteNextHopEntry 16 }
-- MVPN Notifications -- MVPN Notifications
mvpnMvrfChange NOTIFICATION-TYPE mvpnMvrfOperationChange NOTIFICATION-TYPE
OBJECTS { OBJECTS {
mvpnGenMvrfStatusChange mvpnGenMvrfLastOperation
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"A mvpnMvrfChange notification signifies a change about "A mvpnMvrfOperationChange notification signifies a change about
a MVRF in the PE. The change event can be creation of a MVRF in the PE. The change event can be creation of
the MVRF, deletion of the MVRF or an update on the I-PMSI the MVRF, deletion of the MVRF or an update on the I-PMSI
or S-PMSI configuration of the MVRF. The change event or S-PMSI information of the MVRF. The change event
is indicated by mvpnGenMvrfStatusChange embedded in is indicated by mvpnGenMvrfLastOperation embedded in
the notification. The user can then query the notification. The user can then query
mvpnGeneralTable, and/or mvpnSpmsiConfigTable to mvpnGenericTable, mvpnPmsiTable, and/or mvpnSpmsiTable to
get the details of the change as necessary. get the details of the change as necessary.
Note: Since the creation of a MVRF is often followed by Note: Since the creation of a MVRF is often followed by
configuration of I-PMSI and/or S-PMSIs for the MVRF, configuration of I-PMSI and/or S-PMSIs for the MVRF,
more than one (three at most) notifications for a MVRF may more than one (three at most) notifications for a MVRF may
be generated serially, and it is really not necessary to be generated serially, and it is really not necessary to
generate all three of them. An agent may choose to generate a generate all three of them. An agent may choose to generate a
notification for the last event only, that is for S-PMSI notification for the last event only, that is for S-PMSI
configuration. configuration.
Similarly, deletion of I-PMSI and S-PMSI configuration on a Similarly, deletion of I-PMSI and S-PMSI configuration on a
MVRF happens before a MVRF is deleted and it is recommended MVRF happens before a MVRF is deleted and it is recommended
that the agent send the notification for MVRF deletion that the agent send the notification for MVRF deletion
event only. event only.
" "
::= { mvpnNotifications 1 } ::= { mvpnNotifications 1 }
mvpnMvrfGroupJoined NOTIFICATION-TYPE
OBJECTS {
mvpnMrouteTimeStamp
}
STATUS current
DESCRIPTION
"A mvpnMvrfGroupJoined notification signifies that
this PE has joined to a new multicast group
serviced in a particular MVPN.
The change event is indicated by mvpnMrouteTimeStamp
embedded in the notification.
"
::= { mvpnNotifications 2 }
mvpnMvrfGroupLeft NOTIFICATION-TYPE
OBJECTS {
mvpnMrouteTimeStamp
}
STATUS current
DESCRIPTION
"A mvpnMvrfGroupJoined notification signifies that
this PE has left from a multicast group
serviced in a particular MVPN.
The change event is indicated by mvpnMrouteTimeStamp
embedded in the notification.
"
::= { mvpnNotifications 3 }
-- MVPN MIB Conformance Information -- MVPN MIB Conformance Information
mvpnGroups OBJECT IDENTIFIER ::= { mvpnConformance 1 } mvpnGroups OBJECT IDENTIFIER ::= { mvpnConformance 1 }
mvpnCompliances OBJECT IDENTIFIER ::= { mvpnConformance 2 } mvpnCompliances OBJECT IDENTIFIER ::= { mvpnConformance 2 }
-- Compliance Statements -- Compliance Statements
mvpnModuleFullCompliance MODULE-COMPLIANCE mvpnModuleFullCompliance MODULE-COMPLIANCE
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Compliance statement for agents that provide full support "Compliance statement for agents that provide full support
for the MCAST-VPN-MIB for the MCAST-VPN-MIB
" "
MODULE -- this module MODULE -- this module
MANDATORY-GROUPS { MANDATORY-GROUPS {
mvpnScalarGroup, mvpnScalarGroup,
mvpnGeneralGroup, mvpnGenericGroup,
mvpnPmsiConfigGroup, mvpnPmsiGroup,
mvpnSpmsiConfigGroup,
mvpnSpmsiGroup, mvpnSpmsiGroup,
mvpnSpmsiAdvtGroup,
mvpnMrouteGroup, mvpnMrouteGroup,
mvpnMrouteNextHopGroup,
mvpnNotificationGroup mvpnNotificationGroup
} }
GROUP mvpnIpmsiGroup GROUP mvpnIpmsiGroup
DESCRIPTION DESCRIPTION
"This group is mandatory for systems that support "This group is mandatory for systems that support
BGP signaling for I-PMSI. BGP signaling for I-PMSI.
" "
GROUP mvpnInterAsIpmsiGroup GROUP mvpnInterAsIpmsiGroup
DESCRIPTION DESCRIPTION
"This group is mandatory for systems that support "This group is mandatory for systems that support
Inter-AS Segmented I-PMSI. Inter-AS Segmented I-PMSI.
" "
GROUP mvpnBgpGeneralGroup GROUP mvpnBgpGenericGroup
DESCRIPTION DESCRIPTION
"This group is mandatory for systems that support "This group is mandatory for systems that support
BGP-MVPN. BGP-MVPN.
" "
GROUP mvpnOptionalGroup GROUP mvpnOptionalGroup
DESCRIPTION DESCRIPTION
"This group is optional. "This group is optional.
" "
skipping to change at page 31, line 20 skipping to change at page 57, line 4
" "
::= { mvpnCompliances 1 } ::= { mvpnCompliances 1 }
mvpnModuleReadOnlyCompliance MODULE-COMPLIANCE mvpnModuleReadOnlyCompliance MODULE-COMPLIANCE
STATUS current STATUS current
DESCRIPTION "Compliance requirement for implementations that DESCRIPTION "Compliance requirement for implementations that
only provide read-only support for MCAST-VPN-MIB. only provide read-only support for MCAST-VPN-MIB.
Such devices can then be monitored but cannot be Such devices can then be monitored but cannot be
configured using this MIB module. configured using this MIB module.
" "
MODULE -- this module MODULE -- this module
MANDATORY-GROUPS { MANDATORY-GROUPS {
mvpnScalarGroup, mvpnScalarGroup,
mvpnGeneralGroup, mvpnGenericGroup,
mvpnPmsiConfigGroup, mvpnPmsiGroup,
mvpnSpmsiConfigGroup,
mvpnSpmsiGroup, mvpnSpmsiGroup,
mvpnSpmsiAdvtGroup,
mvpnMrouteGroup, mvpnMrouteGroup,
mvpnMrouteNextHopGroup,
mvpnNotificationGroup mvpnNotificationGroup
} }
GROUP mvpnIpmsiGroup GROUP mvpnIpmsiGroup
DESCRIPTION DESCRIPTION
"This group is mandatory for systems that support "This group is mandatory for systems that support
BGP signaling for I-PMSI. BGP signaling for I-PMSI.
" "
GROUP mvpnInterAsIpmsiGroup GROUP mvpnInterAsIpmsiGroup
DESCRIPTION DESCRIPTION
"This group is mandatory for systems that support "This group is mandatory for systems that support
Inter-AS Segmented I-PMSI. Inter-AS Segmented I-PMSI.
" "
GROUP mvpnBgpGeneralGroup GROUP mvpnBgpGenericGroup
DESCRIPTION DESCRIPTION
"This group is mandatory for systems that support "This group is mandatory for systems that support
BGP-MVPN. BGP-MVPN.
" "
GROUP mvpnOptionalGroup GROUP mvpnOptionalGroup
DESCRIPTION DESCRIPTION
"This group is optional. "This group is optional.
" "
OBJECT mvpnNotificationEnable
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
OBJECT mvpnGenCmcastRouteProtocol OBJECT mvpnGenCmcastRouteProtocol
MIN-ACCESS read-only MIN-ACCESS read-only
DESCRIPTION "Write access is not required." DESCRIPTION "Write access is not required."
OBJECT mvpnGenIpmsiConfig OBJECT mvpnGenIpmsiInfo
MIN-ACCESS read-only MIN-ACCESS read-only
DESCRIPTION "Write access is not required." DESCRIPTION "Write access is not required."
OBJECT mvpnGenInterAsPmsiConfig OBJECT mvpnGenInterAsPmsiInfo
MIN-ACCESS read-only MIN-ACCESS read-only
DESCRIPTION "Write access is not required." DESCRIPTION "Write access is not required."
OBJECT mvpnGenUmhSelection OBJECT mvpnGenUmhSelection
MIN-ACCESS read-only MIN-ACCESS read-only
DESCRIPTION "Write access is not required." DESCRIPTION "Write access is not required."
OBJECT mvpnGenSiteType OBJECT mvpnGenCustomerSiteType
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
OBJECT mvpnGenSptnlLimit
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
OBJECT mvpnPmsiConfigEncapsType
MIN-ACCESS read-only MIN-ACCESS read-only
DESCRIPTION "Write access is not required." DESCRIPTION "Write access is not required."
OBJECT mvpnSpmsiConfigThreshold OBJECT mvpnGenSPTunnelLimit
MIN-ACCESS read-only MIN-ACCESS read-only
DESCRIPTION "Write access is not required." DESCRIPTION "Write access is not required."
OBJECT mvpnSpmsiConfigPmsiPointer OBJECT mvpnPmsiEncapsulationType
MIN-ACCESS read-only MIN-ACCESS read-only
DESCRIPTION "Write access is not required." DESCRIPTION "Write access is not required."
OBJECT mvpnGenRowStatus OBJECT mvpnSpmsiThreshold
SYNTAX RowStatus { active(1) }
MIN-ACCESS read-only
DESCRIPTION "Write access is not required."
OBJECT mvpnPmsiConfigRowStatus
SYNTAX RowStatus { active(1) }
MIN-ACCESS read-only MIN-ACCESS read-only
DESCRIPTION "Write access is not required." DESCRIPTION "Write access is not required."
OBJECT mvpnSpmsiConfigRowStatus OBJECT mvpnSpmsiPmsiPointer
SYNTAX RowStatus { active(1) }
MIN-ACCESS read-only MIN-ACCESS read-only
DESCRIPTION "Write access is not required." DESCRIPTION "Write access is not required."
::= { mvpnCompliances 2 } ::= { mvpnCompliances 2 }
-- units of conformance -- units of conformance
mvpnScalarGroup OBJECT-GROUP mvpnScalarGroup OBJECT-GROUP
OBJECTS { OBJECTS {
mvpnMvrfs, mvpnMvrfs,
mvpnV4Mvrfs, mvpnV4Mvrfs,
mvpnV6Mvrfs, mvpnV6Mvrfs,
mvpnPimV4Mvrfs, mvpnPimV4Mvrfs,
mvpnPimV6Mvrfs, mvpnPimV6Mvrfs,
mvpnBgpV4Mvrfs, mvpnBgpV4Mvrfs,
mvpnBgpV6Mvrfs, mvpnBgpV6Mvrfs,
mvpnMldpMvrfs, mvpnMldpMvrfs
mvpnNotificationEnable
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"These objects are used to monitor/manage "These objects are used to monitor/manage
global MVPN parameters. global MVPN parameters.
" "
::= { mvpnGroups 1 } ::= { mvpnGroups 1 }
mvpnGeneralGroup OBJECT-GROUP mvpnGenericGroup OBJECT-GROUP
OBJECTS { OBJECTS {
mvpnGenMvrfStatusChange, mvpnGenMvrfLastOperation,
mvpnGenMvrfStatusChangeTime, mvpnGenMvrfLastOperationTime,
mvpnGenCmcastRouteProtocol, mvpnGenCmcastRouteProtocol,
mvpnGenIpmsiConfig, mvpnGenIpmsiInfo,
mvpnGenInterAsPmsiConfig, mvpnGenInterAsPmsiInfo,
mvpnGenUmhSelection, mvpnGenUmhSelection,
mvpnGenSiteType, mvpnGenCustomerSiteType,
mvpnGenSptnlLimit, mvpnGenSPTunnelLimit
mvpnGenRowStatus
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"These objects are used to monitor/manage "These objects are used to monitor/manage
per-VRF MVPN parameters. per-VRF MVPN parameters.
" "
::= { mvpnGroups 2 } ::= { mvpnGroups 2 }
mvpnPmsiConfigGroup OBJECT-GROUP mvpnPmsiGroup OBJECT-GROUP
OBJECTS { OBJECTS {
mvpnPmsiConfigEncapsType, mvpnPmsiEncapsulationType
mvpnPmsiConfigRowStatus
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"These objects are used to monitor/manage "These objects are used to monitor/manage
PMSI tunnel configurations. PMSI tunnel configurations.
" "
::= { mvpnGroups 3 } ::= { mvpnGroups 3 }
mvpnSpmsiConfigGroup OBJECT-GROUP mvpnSpmsiGroup OBJECT-GROUP
OBJECTS { OBJECTS {
mvpnSpmsiConfigThreshold, mvpnSpmsiThreshold,
mvpnSpmsiConfigPmsiPointer, mvpnSpmsiPmsiPointer
mvpnSpmsiConfigRowStatus
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"These objects are used to monitor/manage "These objects are used to monitor/manage
S-PMSI configurations. S-PMSI configurations.
" "
::= { mvpnGroups 4 } ::= { mvpnGroups 4 }
mvpnIpmsiGroup OBJECT-GROUP mvpnIpmsiGroup OBJECT-GROUP
OBJECTS { OBJECTS {
mvpnIpmsiUpTime, mvpnIpmsiAdvtTunnelAttribute,
mvpnIpmsiAttribute mvpnIpmsiAdvtReceived,
mvpnIpmsiAdvtReceivedError,
mvpnIpmsiAdvtMalformedTunnelType,
mvpnIpmsiAdvtMalformedTunnelId,
mvpnIpmsiAdvtLastReceivedTime,
mvpnIpmsiAdvtCounterDiscontinuityTime
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"These objects are used to monitor/manage "These objects are used to monitor/manage
Intra-AS I-PMSI attributes. Intra-AS I-PMSI attributes.
" "
::= { mvpnGroups 5 } ::= { mvpnGroups 5 }
mvpnInterAsIpmsiGroup OBJECT-GROUP mvpnInterAsIpmsiGroup OBJECT-GROUP
OBJECTS { OBJECTS {
mvpnInterAsIpmsiAttribute mvpnInterAsIpmsiAdvtTunnelAttribute,
mvpnInterAsIpmsiAdvtReceived,
mvpnInterAsIpmsiAdvtReceivedError,
mvpnInterAsIpmsiAdvtMalformedTunnelType,
mvpnInterAsIpmsiAdvtMalformedTunnelId,
mvpnInterAsIpmsiAdvtLastReceivedTime,
mvpnInterAsIpmsiAdvtCounterDiscontinuityTime
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"These objects are used to monitor/manage "These objects are used to monitor/manage
Inter-AS I-PMSI attributes. Inter-AS I-PMSI attributes.
" "
::= { mvpnGroups 6 } ::= { mvpnGroups 6 }
mvpnSpmsiGroup OBJECT-GROUP mvpnSpmsiAdvtGroup OBJECT-GROUP
OBJECTS { OBJECTS {
mvpnSpmsiTunnelAttribute, mvpnSpmsiAdvtTunnelAttribute,
mvpnSpmsiUpTime, mvpnSpmsiAdvtExpTime,
mvpnSpmsiExpTime, mvpnSpmsiAdvtRefCnt,
mvpnSpmsiRefCnt mvpnSpmsiAdvtReceived,
mvpnSpmsiAdvtReceivedError,
mvpnSpmsiAdvtMalformedTunnelType,
mvpnSpmsiAdvtMalformedTunnelId,
mvpnSpmsiAdvtLastReceivedTime,
mvpnSpmsiAdvtCounterDiscontinuityTime
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"These objects are used to monitor/manage "These objects are used to monitor/manage
S-PMSI attributes. S-PMSI attributes.
" "
::= { mvpnGroups 7 } ::= { mvpnGroups 7 }
mvpnMrouteGroup OBJECT-GROUP mvpnMrouteGroup OBJECT-GROUP
OBJECTS { OBJECTS {
mvpnMrouteUpstreamNeighborAddrType,
mvpnMrouteUpstreamNeighborAddr,
mvpnMrouteInIfIndex,
mvpnMrouteTimeStamp,
mvpnMrouteExpiryTime,
mvpnMrouteProtocol,
mvpnMrouteRtProtocol,
mvpnMrouteRtAddrType,
mvpnMrouteRtAddr,
mvpnMrouteRtPrefixLength,
mvpnMrouteRtType,
mvpnMrouteOctets,
mvpnMroutePkts,
mvpnMrouteTtlDropOctets,
mvpnMrouteTtlDropPackets,
mvpnMrouteDifferentInIfOctets,
mvpnMrouteDifferentInIfPackets,
mvpnMrouteBps,
mvpnMroutePmsiPointer,
mvpnMrouteNumberOfLocalReplication, mvpnMrouteNumberOfLocalReplication,
mvpnMrouteNumberOfRemoteReplication mvpnMrouteNumberOfRemoteReplication
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"These objects are used to monitor/manage "These objects are used to monitor/manage
VPN multicast forwarding states. VPN multicast forwarding states.
" "
::= { mvpnGroups 8 } ::= { mvpnGroups 8 }
mvpnBgpGeneralGroup OBJECT-GROUP mvpnMrouteNextHopGroup OBJECT-GROUP
OBJECTS {
mvpnMrouteNextHopState,
mvpnMrouteNextHopTimeStamp,
mvpnMrouteNextHopExpiryTime,
mvpnMrouteNextHopClosestMemberHops,
mvpnMrouteNextHopProtocol,
mvpnMrouteNextHopOctets,
mvpnMrouteNextHopPkts
}
STATUS current
DESCRIPTION
"These objects are used to monitor/manage
next hop information of VPN multicast.
"
::= { mvpnGroups 9 }
mvpnBgpGenericGroup OBJECT-GROUP
OBJECTS { OBJECTS {
mvpnBgpGenMode, mvpnBgpGenMode,
mvpnBgpGenVrfRtImport, mvpnBgpGenVrfRouteImport,
mvpnBgpGenSrcAs mvpnBgpGenSrcAs,
mvpnBgpGenCmcastRouteWithdrawalTimer,
mvpnBgpGenSrcSharedTreeJoinTimer,
mvpnBgpGenMsgRateLimit,
mvpnBgpGenMaxSpmsiAdRoutes,
mvpnBgpGenMaxSpmsiAdRouteFreq,
mvpnBgpGenMaxSrcActiveAdRoutes,
mvpnBgpGenMaxSrcActiveAdRouteFreq
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"These objects are used to monitor/manage BGP-MVPN." "These objects are used to monitor/manage BGP-MVPN."
::= { mvpnGroups 9 } ::= { mvpnGroups 10 }
mvpnOptionalGroup OBJECT-GROUP mvpnOptionalGroup OBJECT-GROUP
OBJECTS { OBJECTS {
mvpnMroutePmsiPointer mvpnMroutePmsiPointer
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Support of these object is not required." "Support of these object is not required."
::= { mvpnGroups 10 } ::= { mvpnGroups 11 }
mvpnNotificationGroup NOTIFICATION-GROUP mvpnNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS { NOTIFICATIONS {
mvpnMvrfChange mvpnMvrfOperationChange,
mvpnMvrfGroupJoined,
mvpnMvrfGroupLeft
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Objects required for MVPN notifications." "Objects required for MVPN notifications."
::= { mvpnGroups 11 } ::= { mvpnGroups 12 }
END END
4. Security Considerations 4. Security Considerations
This MIB contains some read-only objects that may be deemed senstive This MIB contains some read-only objects that may be deemed senstive
by some though perhaps not all operators. It also contains some by some though perhaps not all operators. It also contains some
read- write objects, whose setting will change the device's behavior read- write objects, whose setting will change the device's behavior
related to MVPN. Appropriate security procedures related to SNMP in related to MVPN. Appropriate security procedures related to SNMP in
general but not specific to this MIB need to be implemented by general but not specific to this MIB need to be implemented by
concerned operators. concerned operators.
There are a number of management objects defined in this MIB module There are a number of management objects defined in this MIB module
with a MAX-ACCESS clause of read-write and/or read-create. Such with a MAX-ACCESS clause of read-write and/or read-create. Such
objects may be considered sensitive or vulnerable in some network objects may be considered sensitive or vulnerable in some network
environments. The support for SET operations in a non-secure environments. The support for SET operations in a non-secure
environment without proper protection opens devices to attack. These environment without proper protection opens devices to attack. These
are the tables and objects and their sensitivity/vulnerability: are the tables and objects and their sensitivity/vulnerability:
o mvpnNotificationEnable, mvpnGenCmcastRouteProtocol, o mvpnGenCmcastRouteProtocol, mvpnGenIpmsiInfo,
mvpnGenIpmsiConfig, mvpnGenInterAsPmsiConfig, mvpnGenUmhSelection, mvpnGenInterAsPmsiInfo, mvpnGenUmhSelection,
mvpnGenSiteType, mvpnGenSptnlLimit, mvpnBgpGenMode, mvpnGenCustomerSiteType, mvpnGenSPTunnelLimit, mvpnBgpGenMode,
mvpnBgpGenVrfRtImport, mvpnPmsiConfigEncapsType, mvpnBgpGenVrfRtImport, mvpnPmsiEncapsulationType,
mvpnSpmsiConfigThreshold, mvpnSpmsiConfigPmsiPointer mvpnSpmsiThreshold, mvpnSpmsiPmsiPointer
o mvpnGenRowStatus, mvpnPmsiConfigRowStatus,
mvpnSpmsiConfigRowStatus
Some of the readable objects in this MIB module (i.e., objects with a Some of the readable objects in this MIB module (i.e., objects with a
MAX-ACCESS other than not-accessible) may be considered sensitive or MAX-ACCESS other than not-accessible) may be considered sensitive or
vulnerable in some network environments. It is thus important to vulnerable in some network environments. It is thus important to
control even GET and/or NOTIFY access to these objects and possibly control even GET and/or NOTIFY access to these objects and possibly
to even encrypt the values of these objects when sending them over to even encrypt the values of these objects when sending them over
the network via SNMP. These are the tables and objects and their the network via SNMP. These are the tables and objects and their
sensitivity/vulnerability: sensitivity/vulnerability:
o [TBD] o [TBD]
skipping to change at page 37, line 43 skipping to change at page 64, line 16
This document borrowed some text from Cisco PIM-MVPN MIB This document borrowed some text from Cisco PIM-MVPN MIB
[I-D.svaidya-mcast-vpn-mib]. We would like to thank Yakov Rekhter, [I-D.svaidya-mcast-vpn-mib]. We would like to thank Yakov Rekhter,
Jeffrey Haas, Huajin Jeng, Durga Prasad Velamuri for their helpful Jeffrey Haas, Huajin Jeng, Durga Prasad Velamuri for their helpful
comments. comments.
7. References 7. References
7.1. Normative References 7.1. Normative References
[I-D.ietf-bess-l2l3-vpn-mcast-mib] [RFC2003] Perkins, C., "IP Encapsulation within IP", RFC 2003, DOI
Zhang, Z. and H. Tsunoda, "L2L3 VPN Multicast MIB", draft- 10.17487/RFC2003, October 1996, <https://www.rfc-
ietf-bess-l2l3-vpn-mcast-mib-12 (work in progress), editor.org/info/rfc2003>.
November 2017.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/ Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/
RFC2119, March 1997, <https://www.rfc-editor.org/info/ RFC2119, March 1997, <https://www.rfc-editor.org/info/
rfc2119>. rfc2119>.
[RFC2578] McCloghrie, K., Ed., Perkins, D., Ed., and J. [RFC2578] McCloghrie, K., Ed., Perkins, D., Ed., and J.
Schoenwaelder, Ed., "Structure of Management Information Schoenwaelder, Ed., "Structure of Management Information
Version 2 (SMIv2)", STD 58, RFC 2578, DOI 10.17487/ Version 2 (SMIv2)", STD 58, RFC 2578, DOI 10.17487/
RFC2578, April 1999, <https://www.rfc-editor.org/info/ RFC2578, April 1999, <https://www.rfc-editor.org/info/
skipping to change at page 38, line 21 skipping to change at page 64, line 41
[RFC2579] McCloghrie, K., Ed., Perkins, D., Ed., and J. [RFC2579] McCloghrie, K., Ed., Perkins, D., Ed., and J.
Schoenwaelder, Ed., "Textual Conventions for SMIv2", STD Schoenwaelder, Ed., "Textual Conventions for SMIv2", STD
58, RFC 2579, DOI 10.17487/RFC2579, April 1999, 58, RFC 2579, DOI 10.17487/RFC2579, April 1999,
<https://www.rfc-editor.org/info/rfc2579>. <https://www.rfc-editor.org/info/rfc2579>.
[RFC2580] McCloghrie, K., Ed., Perkins, D., Ed., and J. [RFC2580] McCloghrie, K., Ed., Perkins, D., Ed., and J.
Schoenwaelder, Ed., "Conformance Statements for SMIv2", Schoenwaelder, Ed., "Conformance Statements for SMIv2",
STD 58, RFC 2580, DOI 10.17487/RFC2580, April 1999, STD 58, RFC 2580, DOI 10.17487/RFC2580, April 1999,
<https://www.rfc-editor.org/info/rfc2580>. <https://www.rfc-editor.org/info/rfc2580>.
[RFC2784] Farinacci, D., Li, T., Hanks, S., Meyer, D., and P.
Traina, "Generic Routing Encapsulation (GRE)", RFC 2784,
DOI 10.17487/RFC2784, March 2000, <https://www.rfc-
editor.org/info/rfc2784>.
[RFC2863] McCloghrie, K. and F. Kastenholz, "The Interfaces Group
MIB", RFC 2863, DOI 10.17487/RFC2863, June 2000,
<https://www.rfc-editor.org/info/rfc2863>.
[RFC3032] Rosen, E., Tappan, D., Fedorkow, G., Rekhter, Y.,
Farinacci, D., Li, T., and A. Conta, "MPLS Label Stack
Encoding", RFC 3032, DOI 10.17487/RFC3032, January 2001,
<https://www.rfc-editor.org/info/rfc3032>.
[RFC3414] Blumenthal, U. and B. Wijnen, "User-based Security Model [RFC3414] Blumenthal, U. and B. Wijnen, "User-based Security Model
(USM) for version 3 of the Simple Network Management (USM) for version 3 of the Simple Network Management
Protocol (SNMPv3)", STD 62, RFC 3414, DOI 10.17487/ Protocol (SNMPv3)", STD 62, RFC 3414, DOI 10.17487/
RFC3414, December 2002, <https://www.rfc-editor.org/info/ RFC3414, December 2002, <https://www.rfc-editor.org/info/
rfc3414>. rfc3414>.
[RFC3826] Blumenthal, U., Maino, F., and K. McCloghrie, "The [RFC3826] Blumenthal, U., Maino, F., and K. McCloghrie, "The
Advanced Encryption Standard (AES) Cipher Algorithm in the Advanced Encryption Standard (AES) Cipher Algorithm in the
SNMP User-based Security Model", RFC 3826, DOI 10.17487/ SNMP User-based Security Model", RFC 3826, DOI 10.17487/
RFC3826, June 2004, <https://www.rfc-editor.org/info/ RFC3826, June 2004, <https://www.rfc-editor.org/info/
rfc3826>. rfc3826>.
[RFC4382] Nadeau, T., Ed. and H. van der Linde, Ed., "MPLS/BGP Layer [RFC4382] Nadeau, T., Ed. and H. van der Linde, Ed., "MPLS/BGP Layer
3 Virtual Private Network (VPN) Management Information 3 Virtual Private Network (VPN) Management Information
Base", RFC 4382, DOI 10.17487/RFC4382, February 2006, Base", RFC 4382, DOI 10.17487/RFC4382, February 2006,
<https://www.rfc-editor.org/info/rfc4382>. <https://www.rfc-editor.org/info/rfc4382>.
[RFC5132] McWalter, D., Thaler, D., and A. Kessler, "IP Multicast [RFC4659] De Clercq, J., Ooms, D., Carugi, M., and F. Le Faucheur,
MIB", RFC 5132, DOI 10.17487/RFC5132, December 2007, "BGP-MPLS IP Virtual Private Network (VPN) Extension for
<https://www.rfc-editor.org/info/rfc5132>. IPv6 VPN", RFC 4659, DOI 10.17487/RFC4659, September 2006,
<https://www.rfc-editor.org/info/rfc4659>.
[RFC5591] Harrington, D. and W. Hardaker, "Transport Security Model [RFC5591] Harrington, D. and W. Hardaker, "Transport Security Model
for the Simple Network Management Protocol (SNMP)", STD for the Simple Network Management Protocol (SNMP)", STD
78, RFC 5591, DOI 10.17487/RFC5591, June 2009, 78, RFC 5591, DOI 10.17487/RFC5591, June 2009,
<https://www.rfc-editor.org/info/rfc5591>. <https://www.rfc-editor.org/info/rfc5591>.
[RFC5592] Harrington, D., Salowey, J., and W. Hardaker, "Secure [RFC5592] Harrington, D., Salowey, J., and W. Hardaker, "Secure
Shell Transport Model for the Simple Network Management Shell Transport Model for the Simple Network Management
Protocol (SNMP)", RFC 5592, DOI 10.17487/RFC5592, June Protocol (SNMP)", RFC 5592, DOI 10.17487/RFC5592, June
2009, <https://www.rfc-editor.org/info/rfc5592>. 2009, <https://www.rfc-editor.org/info/rfc5592>.
skipping to change at page 39, line 30 skipping to change at page 66, line 21
Qiu, "Wildcards in Multicast VPN Auto-Discovery Routes", Qiu, "Wildcards in Multicast VPN Auto-Discovery Routes",
RFC 6625, DOI 10.17487/RFC6625, May 2012, RFC 6625, DOI 10.17487/RFC6625, May 2012,
<https://www.rfc-editor.org/info/rfc6625>. <https://www.rfc-editor.org/info/rfc6625>.
[RFC7761] Fenner, B., Handley, M., Holbrook, H., Kouvelas, I., [RFC7761] Fenner, B., Handley, M., Holbrook, H., Kouvelas, I.,
Parekh, R., Zhang, Z., and L. Zheng, "Protocol Independent Parekh, R., Zhang, Z., and L. Zheng, "Protocol Independent
Multicast - Sparse Mode (PIM-SM): Protocol Specification Multicast - Sparse Mode (PIM-SM): Protocol Specification
(Revised)", STD 83, RFC 7761, DOI 10.17487/RFC7761, March (Revised)", STD 83, RFC 7761, DOI 10.17487/RFC7761, March
2016, <https://www.rfc-editor.org/info/rfc7761>. 2016, <https://www.rfc-editor.org/info/rfc7761>.
[RTPROTO] IANA, "IP Route Protocol MIB", 2016,
<http://www.iana.org/assignments/ianaiprouteprotocol-mib>.
7.2. Informative References 7.2. Informative References
[I-D.svaidya-mcast-vpn-mib] [I-D.svaidya-mcast-vpn-mib]
Vaidya, S., "Multicast in BGP/MPLS IP VPNs Management Vaidya, S., "Multicast in BGP/MPLS IP VPNs Management
Information Base", draft-svaidya-mcast-vpn-mib-02 (work in Information Base", draft-svaidya-mcast-vpn-mib-02 (work in
progress), March 2005. progress), March 2005.
[RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart, [RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart,
"Introduction and Applicability Statements for Internet- "Introduction and Applicability Statements for Internet-
Standard Management Framework", RFC 3410, DOI 10.17487/ Standard Management Framework", RFC 3410, DOI 10.17487/
 End of changes. 296 change blocks. 
603 lines changed or deleted 1889 lines changed or added

This html diff was produced by rfcdiff 1.46. The latest version is available from http://tools.ietf.org/tools/rfcdiff/